Looking For 10" Long Trailer Ramp Springs For 1-1/2" Shaft

Question

Question:

Hello I’m looking for trailer ramp springs. 1 1/2 solid stock, 10" long Left and right 2k lbs. Thank

asked by: Jack

0

Expert Reply:

Hey Jack, thanks for reaching out. What I recommend for you are the Ramp Springs # M376FR for left hand and # M366FR for right hand side. These are 2K rated springs designed for a 1-1/2" shaft. They are 10" long overall.

expert reply by: Jesse M

0

Vince

3/23/2025

I have a snowmobile trailer with 3 10" springs with what appears to have all RH springs. Dose that seem correct all being the same RH thanks in advance

Jesse M.

3/24/2025

@Vince Generally for this style of ramp spring there would be a LH and RH side spring. It could be that whoever built the trailer simply used all RH springs because that was all they had access to. I have heard of people doing that in a pinch and it working fine. The orientation of the spring legs would be different but it would essentially still work the same.

Answer 1

The right and left trailer ramp springs #RS16933RH and #RS16933LH will install on the passenger and driver sides of your trailer ramp, respectively. Usually right hand springs will have a painted end for identification while left springs do not.

view full answer...

Answer 2

We have the Dexter Hub and Drum part #8-219-9UC3-A which is a 7k oil bath hub and drum. It would fit your current axle perfectly and allow you to convert it to oil bath.

view full answer...

Answer 3

Hi Jerry; an air compensated pintle hook like the Buyers Products 50 Ton Air Compensated Pintle Hook with Chamber and Plunger #337PH50AC is going to be the best option. However, none of our pintle hitch plates like the #3371809040 you looked at have…

view full answer...

Answer 4

While we don't have any custom fit hitch plates that fit your 2016 International 4300 we do have some universal mounts that would potentially work. You'd need to have a qualified welder install the kit. The hitch plates below all come with…

view full answer...

Answer 5

While there isn't a 3D model available, I was able to verify with the manufacturer and get a small diagram of the mounting hole dimensions of the Buyers Products 10 Ton Pintle Hook #337PH10. The mounting holes are exactly 0.531" in diameter,…

view full answer...

Answer 6

The Buyers Products 45 Ton Pintle Hook #337PH45 does not have the 4 inch square bolt pattern but rather uses a different pattern. Vertically the holes are 3 inches on center. Horizontally the top row is 5-1/4 inches on center and the bottom is 6-1/2…

view full answer...

Answer 7

Hey Chris, so I am afraid we do not carry a spring that will work for your trailer. We do have the #M366FR and #M376FR torsion springs that are made for a 1-1/2" shaft. Right now, this is the only size we offer, so nothing for a 2-3/4" or…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Looking For 10" Long Trailer Ramp Springs For 1-1/2" Shaft

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching