Suspension Enhancement Recommendation for a 2026 Toyota Tacoma for Hauling

Question

Question:

I'm needing to add some help to my suspension to my Toyota Tacoma 2026. I use my truck mainly for hauling, but I'd like to use the kit for occasional towing as well.

asked by: Wayne

0

Expert Reply:

Hey Wayne,

The Air Lift LoadLifter 5000 Air Helper Springs # AL45DQ are the best for your situation because they are able to be adjusted for specific loads in your truck bed. Since you do a lot of hauling this gives you the ability to customize how much support you need for each load so you get the best suspension performance every time.

Something else that would be helpful for your consistent hauling is the Air Lift WirelessONE Compressor System # AL25980 which enables you to monitor and adjust the air bags on the fly. So, if you're changing your load fairly often this kit is just increasing your quality of life so it's easier to get the air bags to the right pressure.

expert reply by: Jon G

0

Jon G.

11/17/2025

Hey Wayne, how did the Air Lift LoadLifter 5000 springs work out on your Tacoma for hauling and towing? It’d be great to hear if the adjustable support made a difference in your ride quality. Your update could make it easier for others setting up a similar suspension.

Answer 1

Hello Jason, Congrats on the new ride! What is your new favorite feature? The Air Lift LoadLifter 5000 kit for your 2025 Tacoma is made to support heavy loads and towing by adding extra cushion between the frame and axle. When you’re driving normally…

view full answer...

Answer 2

Hello Rick, thanks for reaching out. The Air Lift LoadLifter 5000 Air Helper Springs #AL45DQ are correct for the 2024 Tacoma. Air lift does make spring cradles that can be used with their LoadLifter 5000 air bags. For that, you can use the following:…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hey Sean, yes you can use the TowSmart Adjustable Ball Mount #TS89VR in the Gen-Y Voyager Ball Mount #GY52JJ. This will provide cushioning to the adjustable ball mount plus some additional drop. What are you planning on towing with this setup?

view full answer...

Answer 9

Hey Josh! Yes, the Pacbrake Alpha XD Pro Air Bag Suspension Kit w/ Internal Jounce Bumpers #PB89RV will fit your Sprinter. This is specifically designed for models with dual rear wheels. The only reason these wouldn't work is if you have the ride…

view full answer...

Answer 10

Hello Barry, Since you already have a weight distribution (WD) hitch and are only experiencing a little rear sag, I recommend going with SumoSprings. I typically only suggest Timbrens for those who are towing heavy loads regularly, as they can create…

view full answer...

Answer 11

Hi Todd, I know exactly the feeling you’re describing, and you’re definitely not alone. That floaty, pushy feeling at highway speeds, especially when trucks pass, is really common on the Sprinter 3500 chassis with a taller coach like your Tiburon,…

view full answer...

Answer 12

Hi Bill! Thanks for your pictures, they were extremely helpful! ^___^ The LCI Part #194170 on that tag you found means you have a 1621 pin box. The Gen-Y #GY45SR you were looking at is specifically for the Lippert 1116 and 1716 pin boxes, so you will…

view full answer...