Air Lift Air Spring Kit for 2022 Toyota Highlander XLE

Question

Question:

Hello, we have a 2022 Toyota Highlander XLE AWD. Which Air Lift suspension kit would you recommend for our vehicle? Thanks

asked by: Pete

0

Expert Reply:

Hello again Pete; you have the right idea looking at the Air Lift 1000 Universal Air Spring Kit # AL57TV. There are no custom fit options for your 2022 Toyota Highlander XLE so the only solution is one of these universal kits. To find the right one you will need to take some measurements.

First, unload your vehicle to make sure it's at normal ride height. Then, measure the inside height of your coil spring, which will be from the upper spring seat to the lower spring seat. Lastly, measure the inside diameter of the spring at its widest point. Once you have these measurements, use the table below to find the correct kit by matching up your diameter and height values.

For example, the # AL57TV fits a minimum diameter of 5-1/2" and maximum height of 10-1/2". If this matches what you have you can use this kit for your Highlander. If not, select the kit that corresponds to your measurements on the table.

expert reply by: Robin H

0

Air Lift Universal Spring Measurement.
(click to enlarge)

Air Lift Universal Spring Table.
(click to enlarge)

Robin H.

12/15/2025

Hey Pete, were you able to take those coil spring measurements on your Highlander to see if the Air Lift 1000 kit fits? Once you know the height and diameter, it should be easy to match the right kit. Let me know what you found—I can help confirm the best fit.

Oric

8/1/2026

@RobinH I measured the size of Toyota Highlander 2022 AWD v6 Before lift by jack , it is 4.5” ( min dia inside springs) x 4.5” ( high ) If lift by jack, tire sit in the air, it is 4.5” ( min dia inside springs) x 6” ( high ) No air outlet either on top or bottom I think we need to drill a hole at bottom to allow pipe go out. Also no good fit size for 4.5” x 4.5” It’s unfortunate that Toyota Highlander Gen4 owners’ needs for an air lift product were overlooked.

Answer 1

The SumoSprings kit part #CSS-1145R is exactly what you are looking for. This will give the rear suspension of your 2021 Toyota Highlander additional support to get rid of the sagging you mentioned. You are right that a weight distribution system…

view full answer...

Answer 2

Since your vehicle does not have a brake controller port, you will want to use a universal wiring pigtail. For example, if you have a Tekonsha brake controller, you could use a Plug-In Harness for Tekonsha and Draw-Tite Brake Controllers #20127. You…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Air Lift Air Spring Kit for 2022 Toyota Highlander XLE

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching