Recommended 30" Long Metal Trailer Fender for a Camper

Question

Question:

Hello! Im looking for a metal fender for my camper that is 30 L X 12 H X 10 W and I cant find one anywhere. Can you help me find one? Thanks! Marshall

asked by: Marshall W

0

Expert Reply:

Marshall, the closest fender we carry is the Single Axle Trailer Fender for Boat Trailers # HP38VR. This fender measures 30" long, 9" wide, 13 1/4" tall, is made of metal, and can be bolted on or welded on.

expert reply by: Bryce D

0

Heather A.

12/22/2025

Hey Marshall, did that metal fender with the 30-inch length and 9-inch width end up working for your camper? Your update could make it easier for the next person trying to match those same dimensions.

Marshall W.

12/22/2025

@HeatherA It sure did not. I ended up taking the other fender off and buying a new pair to replace both. Time consuming, but looked great when I was done. I looked for the direct replacement fender for a month or so before giving up. Best of luck to you!

Answer 1

Yes you certainly can. In order to bolt-on a set of metal weld-on fenders such as the Single Axle Trailer Fender part #HP29VR you will need a set of mounting brackets such as the Mounting Brackets for Trailer Fender part #CE26098G-2. If you do not…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 11

Thanks for the pics Kemo, they really helped! The CE Smith Single Axle Trailer Fenders #CE19504-2 are larger than what you currently have and use a different mounting style. Based on your setup, the CE Smith Fenders wouldn’t bolt onto your existing…

view full answer...

Answer 12

Hello Kirt, thanks for reaching out. The Fulton Single Axle Trailer Fenders #F008595-2 are the closest thing we offer to the Ez-loader 250-023712-10 fenders you are looking for. The Fulton #F008595-2 fenders are gray in color and they are…

view full answer...

Recommended 30" Long Metal Trailer Fender for a Camper

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching