Opening of the TowSmart Threaded Quick Links for Safety Chains

Question

Question:

What is the opening dimension on 348749M?

asked by: Rob

0

Expert Reply:

Rob, the opening of the TowSmart Threaded Quick Links for Safety Chains # 348749M is 5/16" wide.

expert reply by: Bryce D

0

Opening width of the TowSmart Threaded Quick Links
(click to enlarge)

Rob

10/17/2024

Thanks, I need 7/16". Is there another with that opening size?

Bryce D.

10/18/2024

@Rob Yes, we do, check out the Replacement Roadmaster Quick Links for Safety Cables # RM-910022. These links have the 7/16" opening you're looking for and has a nice 10,000 lb weight capacity.

Answer 1

Hey Mark, so the CE Smith chain part #CES42QR has a diameter of 1/4 inch which means the inside width of the chain link is .43 inch which is the max diameter bolt that could pass through it.

view full answer...

Answer 2

The proper replacement heating element for your Dometic GC6AA-10E is the Camco #CAM02103. Because the element is accessed from the rear of the unit, Dometic recommends having a qualified service center complete the installation. A specific socket is…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Opening of the TowSmart Threaded Quick Links for Safety Chains

Product Page this Question was Asked From

Continue Researching