What is Diameter of U-Bolt Malone Anti Rattle MPG908

Question

Question:

What is the U bolt diameter? !/2 inch or is it smaller? SAE threads or metric?

asked by: Richard F

0

Expert Reply:

Hey Richard, the diameter of the U-bolt that comes with the Malone anti rattle part # MPG908 is 1/2 inch and the threads are metric.

expert reply by: Jameson C

0

Richard F.

10/15/2024

Thank you.

Jameson C.

10/15/2024

@RichardF No prob!

Answer 1

The curve in the Malone Anti-Rattle HitchLock System part #MPG908 is designed for extra stability to not allow the shank of the accessory to move up and down. It is what holds the shank of accessory tight. I have attached a photo of how this is…

view full answer...

Answer 2

Hey Keith, yes the Malone anti rattle device part #MPG908 does work on a Class 4 2 inch hitch like what you have. The reason it is listed as Class II 1-1/4 inch hitch is because only the Class II hitches have the lip around the end of the hitch…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 11

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 12

Hey Tom, great question! Both products provide an easy way to measure tongue weight, but they excel in different situations. The BTBRV Trailer Jack Foot Scale #BTBRV014 measures tongue weight at the trailer jack, so you don't need to position a…

view full answer...

What is Diameter of U-Bolt Malone Anti Rattle MPG908

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching