Is the Replacement Plunger Door Sensor w/ Striker Plates a Normally Open or Closed Switch

Question

Question:

Is this a normally open or normally closed switch? When the button is pushed in by the door are the contacts open or closed?

asked by: Bruce B

0

Expert Reply:

Hey Bruce, I spoke with Lippert and they ensured me that the Replacement Plunger Door Sensor with Striker Plates for Kwikee Electric RV Steps # LC379388 is a normally closed switch.

expert reply by: Bryce D

0

Bruce B.

10/15/2024

Bryce, I ordered the switch you recommended and it arrived today. Problem is it is the same as the one I have with normally open contacts. The contacts are open until the button is depressed. The stamped number on the face of the switch, 9270 is the same on my original switch and the replacement I purchased. I believe the switch I need is Part Number: LC379407. For that one the contacts are closed until the button is pressed. I will also need to return the original switch for credit. thanks, Bruce Bakker

Bryce D.

10/16/2024

@BruceB That's interesting Bruce because I spoke with Lippert directly and they assured me that the Replacement Plunger Door Sensor # LC379388 was a normally closed switch so that's weird that it wouldn't be that way. The switch # LC379407 is normally open so I don't think that this would be the switch you need if you need a normally closed.

Bruce B.

10/16/2024

I'm not sure what 'normally closed'' is on these switches. I had the steps on my RV replaced and they worked backwards. The steps were purchased from you so I asked the question why and was told that some RV's used a normally open switch and if you put in a normally closed switch they would work correctly. That's why I asked the question. The 379388 is the same as the switch I had and hopefully the 379407 is the opposite. I believed that normally open meant that when the button is out, when the door is open, the circuit is open. That's what the 379388 is. So I have ordered a 379407 and hopefully it will be closed when the button is out. The 379388 has the same number stamped on the front, 9270, as is the one in my RV. According to the pictures the 379507 is stamped 9269. Hopefully it is different and will work. The other switch should be here by Friday and I will let you know how it works. Customer service is arranging for the return of the first switch.

Bryce D.

10/16/2024

@BruceB I see. Okay, well let us know how that goes for you, hopefully better!

See All (5) Replies to Bruce B. ∨

Answer 1

Hey Mitch! You can use the RV Propane Gas Detector - 12 Volt - 2 Wire - Black #RS44FR to replace your existing detector. However, you will need to remove the old detector and valve, then reconnect the line with the appropriate fitting. There isn’t a…

view full answer...

Answer 2

Hello Bob. We do have a good gas detector option for you, but the lp gas detector model 7719 is currently unavailable. What I recommend instead is the RV Propane Gas Detector #RS44FR. This is a pretty standard gas detector. Just keep in mind the…

view full answer...

Answer 3

Pretty much any bike rack that holds the bikes strictly by the wheels like the Kuat Sherpa #SH12G is not going to be a good choice for a bike with fenders. A better option for your bike is the Swagman Chinook #S64683 that holds the bike by wheels…

view full answer...

Answer 4

Bruce, this is fairly common, and the issue is usually with motorhomes that are wired to work with a normally open circuit and the steps being meant for a closed circuit. To fix the issue, you'll just need to use the Replacement Door Switch for…

view full answer...

Answer 5

The Lippert Components Kwikee Pleated Plunger Door Switch #LC379407 is a normally open switch. If you're in need of a normally closed switch, you can use the Lippert Components Kwikee 3/4" Core Round Magnetic Door Switch part #LC379400. The…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Is the Replacement Plunger Door Sensor w/ Striker Plates a Normally Open or Closed Switch

Product Page this Question was Asked From

Continue Researching