Does Mounting The Draw-Tite Class 3 Hitch DT28GR Make It Part Of The Chassis?

Question

Question:

Just curious if the mounting is actually part of the chassis? Thank you.

asked by: Carlos B

0

Expert Reply:

Hello Carlos, thanks for reaching out. The Draw-Tite Class 3 Hitch # DT28GR is the correct fit for your 2024 Toyota Corolla Cross. Installation requires permanent removal of the impact structure behind the bumper. The hitch goes in place of the impact structure and takes over its functionality. So the hitch basically is now a permanent part of the chassis.

expert reply by: Jesse M

0

Jesse M.

1/5/2026

Hey Carlos, how did things go with the Draw-Tite hitch on your Corolla Cross after the install? It sounds like it becomes a solid part of the chassis once mounted. Sharing how it turned out could help others thinking about the same upgrade.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Hi Mary, The Draw-Tite Max-Frame Trailer Hitch Receiver #DT28GR has a class III rating and is confirmed to fit your 2024 Toyota Corolla Cross Hybrid. It has a 300lb tongue weight capacity so you'd have to stay under that with anything you'd…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver #C64DR weighs in at about 25 lbs while the Draw-Tite Max-Frame Trailer Hitch Receiver #DT28GR weighs in at about 26 lbs so they are basically identical for your 2022 Toyota Corolla Cross. The only difference between…

view full answer...

Answer 4

Hello Pat. Yes, the Draw-Tite Hitch #DT28GR will indeed fit the 2024 Toyota Corolla Cross Hybrid XSE. I double checked with the manufacturer, and they confirmed that this hitch will fit all models of the 2024 Corolla Cross, so that includes the…

view full answer...

Answer 5

I do not have any information on the factory hitch for the 2024 Toyota Corolla Cross John so I can not speak to the discrepancies on the torque specs. What I can tell you is that both the Draw-Tite item #DT28GR and Curt item #C64DR hitches have been…

view full answer...

Answer 6

Hi Mary, There can be differences in the way components under the vehicle are ran that can change how a trailer hitch will need to be shaped to fit depending on the model type. I spoke with EcoHitch and they stated that they haven't tested the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Does Mounting The Draw-Tite Class 3 Hitch DT28GR Make It Part Of The Chassis?

Continue Researching