Torque Specifications of M14 Bolts Used to Install Draw-Tite # 75699 on 2013 Jeep Grand Cherokee

Question

Question:

product code 75699 draw title hitch. I watched the video on how to install and saw I have to torque the screws down. Can you supply the what torque setting I have to use? Thanks

asked by: Eric

1

Helpful Expert Reply:

If you click on the link to the installation instructions, at the bottom of the instruction sheet, right under the step-by-step run through of the install steps, you'll see the torque specs. We don't publish them because the hitch manufacturers sometimes change them.

I've linked you to an installation video you might find helpful.

expert reply by: Mike L

1

click to enlarge

Answer 1

If you want to install the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13182 on your 2016 Jeep Grand Cherokee, you will use M14 bolts that are grade 5 as well as compatible flat washers. That is the replacement for what is…

view full answer...

Answer 2

If your 2018 Jeep Grand Cherokee has the factory tow package and you are using the Curt T-Connector Vehicle Wiring Harnesse #C55774 you will need to go to your local Jeep dealer and have them re-flash your Jeep's computer in order to activate the…

view full answer...

Answer 3

Since you do not have the removable panel for the rear hitch opening of your 2018 Jeep Grand Cherokee the hitch you'd want is the etrailer part #e98901. This hangs below the rear bumper completely and will give you a higher capacity 2 inch…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Torque Specifications of M14 Bolts Used to Install Draw-Tite # 75699 on 2013 Jeep Grand Cherokee

Featured Help Information

Miscellaneous Media

Continue Researching