Replacement Manual Override Cap For A Ram 3,500lb Electric Tongue Jack

Question

Question:

I am looking for a replacement cap for my RAM electric 3.500lb jack. Here’s a shot of the cap. It didn’t feel like I could get it out without it crumbling completely.

asked by: Jeremy

0

Expert Reply:

Hey Jeremy,

I got the replacement cap # e92ZV added to our selection. A picture will be up as soon as we get one in stock and over to the photo department, but this is going to be that teardrop shaped plug just like you have on your jack.

expert reply by: Kevin C

0

manual override plug
(click to enlarge)

Jeremy A.

9/10/2024

Kevin, Awesome, thanks so much for your fast response on this.

Answer 1

Hi Terry, I went out to the warehouse to measure the Replacement Rubber Cap for etrailer and Ram Jacks part #e92ZV. The outer diameter of the cover that fits into the jack is 1 3/8" wide and the inner diameter of the cover is 1 1/8" wide.…

view full answer...

Answer 2

For a Ram 3,500 lb jack we have the replacement Light Switch #EJ-3520-LSW and Power Switch #EJ-3520-PSW. If you remove the cover you should be able to then pop the switches out of the head to replace them. There should also be the blade-style wiring…

view full answer...

Answer 3

We do indeed have replacement switches - both the power and light switch - as well as cover for your Electric Jack w/ Footplate #EJ-3520-BBX. I'm not sure which switch you need so I'll go ahead and list out both for you, as well as the…

view full answer...

Answer 4

If you take a look at the diagram I've provided for the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW which goes to the Electric Jack w/ Footplate #EJ-3520-WBX, you'll be able to see how both of the…

view full answer...

Answer 5

It sounds like you have either the Electric Jack w/ Footplate part #EJ-3520-BBX or the Electric Jack w/ Footplate part #EJ-3520-WBX. If that is the case then the Replacement Power Switch part #EJ-3520-PSW is the correct replacement for you. In order…

view full answer...

Answer 6

I have attached a photo you can use to connect the Replacement Power Switch #EJ-3520-PSW to your 3,500 lb RAM jack. We don't have a direct wiring diagram but if you notice even though the wires are the same colors they look pretty different so…

view full answer...

Answer 7

I attached a picture that I got from RAM jacks that shows how the RAM Jack switch part #EJ-3520-PSW that you referenced gets wired up.

view full answer...

Answer 8

To replace a switch on your RAM 3,500 lb jack you just need the Replacement Power Switch #EJ-3520-PSW, but this also could be a bad internal screw. To determine if it's the switch or the screw you just need to remove the plug on top of the jack…

view full answer...

Answer 9

I have a replacement jack option for you, but unfortunately the motor for your RAM 3500lb A-Frame Electric trailer jack is not a replaceable part. Instead you will need to replace the entire jack. The Electric Jack w/ Footplate - A-Frame -…

view full answer...

Answer 10

If you've got an Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black #EJ-3520-BBX, which is the same as the Ram 3500-lbs A-frame jack, then the correct part you're looking for is the Replacement Manual Override Cap for…

view full answer...

Answer 11

To verify if the Replacement Power Switch #EJ-3520-PSW will fit your jack you will need to remove to the cover and verify it also uses the 6 wire connection and the opening for the switch is 1" by 1-1/2". I was not able to find any…

view full answer...

Answer 12

If you can reply to this email with the pictures I can help you out. Just be sure to let me know what the product is they are installed on!

view full answer...

Replacement Manual Override Cap For A Ram 3,500lb Electric Tongue Jack

Product Page this Question was Asked From

Continue Researching