What is the Inner and Outer Diameter of the etrailer Replacement Rubber Cap part # e92ZV?

Question

Question:

QUestion about your Replacement Rubber Cap for etrailer or RAM Electric Trailer Jack I have an older elecric trailer jack and the rubber cap is bad. No names or UD on the jack? What size hole does this fit? Thanks

asked by: Terry H

0

Expert Reply:

Hi Terry,

I went out to the warehouse to measure the Replacement Rubber Cap for etrailer and Ram Jacks part # e92ZV. The outer diameter of the cover that fits into the jack is 1 3/8" wide and the inner diameter of the cover is 1 1/8" wide. You'll need to measure the inner diameter of your trailer jack to see if this plug will work for you.

expert reply by: Claire H

0

Answer 1

For a Ram 3,500 lb jack we have the replacement Light Switch #EJ-3520-LSW and Power Switch #EJ-3520-PSW. If you remove the cover you should be able to then pop the switches out of the head to replace them. There should also be the blade-style wiring…

view full answer...

Answer 2

Hey Jeremy, I got the replacement cap #e92ZV added to our selection. A picture will be up as soon as we get one in stock and over to the photo department, but this is going to be that teardrop shaped plug just like you have on your jack.

view full answer...

Answer 3

We do indeed have replacement switches - both the power and light switch - as well as cover for your Electric Jack w/ Footplate #EJ-3520-BBX. I'm not sure which switch you need so I'll go ahead and list out both for you, as well as the…

view full answer...

Answer 4

If you take a look at the diagram I've provided for the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW which goes to the Electric Jack w/ Footplate #EJ-3520-WBX, you'll be able to see how both of the…

view full answer...

Answer 5

It sounds like you have either the Electric Jack w/ Footplate part #EJ-3520-BBX or the Electric Jack w/ Footplate part #EJ-3520-WBX. If that is the case then the Replacement Power Switch part #EJ-3520-PSW is the correct replacement for you. In order…

view full answer...

Answer 6

To verify if the Replacement Power Switch #EJ-3520-PSW will fit your jack you will need to remove to the cover and verify it also uses the 6 wire connection and the opening for the switch is 1" by 1-1/2". I was not able to find any…

view full answer...

Answer 7

Hello David, Thank you for the picture, it was most helpful! It looks like you purchased the Replacement Cover for etrailer and Ram Electric A-Frame Jacks - Black #EJ-3520-BCV and are transferring your old switches. From the picture you sent in, the…

view full answer...

Answer 8

Hey Mike, the correct replacement power switch for your Ram EJ3550 is the part #EJ-3520-PSW.

view full answer...

Answer 9

RAM jacks provided the attached photo showing how the various single and doubled wires connect to the pins on the back of the power switch #EJ-3520-PSW. They do not offer a separate wiring diagram.

view full answer...

Answer 10

I can definitely help! While we do not have access to a complete wiring diagram when installing the Replacement Power Switch #EJ-3520-PSW along with the Replacement Light Board #EJ-3520-LT, we do have an image of the wiring hookup required. Even…

view full answer...

Answer 11

If you are referring to the Electric Jack w/ Footplate part #EJ-3520-BBX for black or part #EJ-3520-WBX for white then yes, we do have the correct replacement extend/retract switch and for this you will want to use the Replacement Power Switch for…

view full answer...

Answer 12

I attached a picture that I got from RAM jacks that shows how the RAM Jack switch part #EJ-3520-PSW that you referenced gets wired up.

view full answer...

What is the Inner and Outer Diameter of the etrailer Replacement Rubber Cap part # e92ZV?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching