Why Would Dexter Actuator Be Tight on Hitch Ball
Updated 01/28/2026 | Published 08/22/2024
Question:
I purchased this brake actuator in march. It was your order number 120523131. It is for a 2” ball. I have a 2” ball. When I am done towing it is very difficult to remove the actuator from the ball. It seems to be too tight of a fit. I have covered the ball in grease, it doesn’t seem to help much. Is there a way to adjust the tightness on this actuator?
asked by: Jeremy L
Expert Reply:
Was it always a tight fit or did it get tighter over time? It's not adjustable so I'm curious if maybe the ball portion of the coupler has dirt or something built up in it that is making it a tight fit.
Product Page this Question was Asked From
Dexter Surge Brake Actuator - Disc - Elec Lockout - 2" Ball - Zinc - 7.5K - 3" x 5"
- Brake Actuator
- Surge Brake Actuator
- Farm Trailer
- Boat Trailer
- Construction Trailer
- Travel Trailer
- Utility Trailer
- Bolt-On
- 7500 lbs GTW
- 2 Inch Ball Coupler
- 3 Inch Channel Tongue
- Disc Brakes
- Electric Lockout
- Dexter
more information >
Continue Researching
- Shop: Dexter DX7.5L A-60L Surge Brake Actuator w Electric Lockout - Disc - 2" Ball - Primed - 7.5K
- Shop: Dexter DX7.5L A-60L Surge Brake Actuator with Fill Cap - Drum - 2" Ball - Primed - 7.5K
- Shop: Dexter Zinc-Plated, A-60 Coupler - 2" Ball - 3" Channel - Bolt On - 5,000 lbs
- Shop: Replacement Inner Member Dexter A84 Actuator - Triple Axle w/Disc Brakes - 2-5/16" Ball - 8.4K
- Search Results: trailer tires and wheels
- Shop: Trailer Hitch
- Video: Measuring To Choose The Right Trailer Axle
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Q&A: Are Powder Coat Trailer Wheels Good for a Saltwater Boat Trailer ST205/75R14
- Shop: Trailer Wiring
- Search Results: trailer jack
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: spare tire mount
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Article: Trailer Lighting Requirements
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Shop: Suspension Enhancement
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Video: In-Depth Review of the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles
- Q&A: Which is Better for Highway Use 4.80-12 or 5.30-12 Trailer TIres
- Search Results: trailer leaf springs
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Video: All About the Demco Hydraulic Brake Actuator-DM72VR
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Shop: Gooseneck Hitch
on Brake Actuator
Jameson C.
1/27/2026
Hey, did you notice if the brake actuator stayed tight or loosened up after checking for dirt or buildup inside the coupler? Sharing what you found could help others who run into the same issue.