Length of Performance Tool 4-Way Folding Lug Wrench

Question

Question:

What is the length of the wrench?

asked by: Luke

0

Expert Reply:

Hey Luke,

The 4-Way Folding Lug Wrench # PTW7 measures 15 inches in length.

expert reply by: Kyle S

0

Jerred H.

1/27/2026

Hey Luke, did the 15-inch length on the folding lug wrench work well for your needs? Knowing how it handled could help others looking for a similar tool.

Answer 1

You bet! The #AM57PR wheel you'd looked at will work great with a 4.80-12 tire.

view full answer...

Answer 2

For your spare tire on your 2015 Nissan Titan SV, I recommend the 4-Way Folding Lug Wrench #PTW7 which will allow you to loosen and tighten the lug nuts on your wheels with ease. It also gives you a compact storage when not in use. For your jack, I…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Hey Mark, since we know your 2022 Imagine 2400BH trailer has 3,500 lb axles the correct bearing kit would be the part #TMK52VR. Bearing replacements are all based on the axle capacity of the trailer. Are you looking to have a spare set on hand or do…

view full answer...

Length of Performance Tool 4-Way Folding Lug Wrench

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching