What Size Bolts Hold Fulton Spare Tire Carrier to Trailer and the Wheel to the Carrier

Question

Question:

Can you tell me the bolt diameter of the Carrier to Frame bolts and the Carrier to Spare bolts? Thank you.

asked by: David F

1

Helpful Expert Reply:

I went out to the warehouse and pulled Fulton Hi-Mount Spare Tire Carrier # FSTC1000301 to measure the bolts with a bolt measuring tool. The bolts that hold the carrier to the trailer frame are 3/8 inch coarse threaded bolts. And the bolts that hold the wheel to the carrier are 1/2 inch coarse threaded bolts.

expert reply by: Michael H

1

Answer 1

I do understand what you mean about the measurements that you took. As long as the bead seat to bead seat measurement is 6" then any of our 225/75R15 tires will fit. I recommended the Kenda Karrier ST225/75R15 Radial Trailer Tire #AM10303. This…

view full answer...

Answer 2

Mod wheels such as the one in tire and wheel combo #LHACK121 have the distinctive round holes. A "regular" trailer wheel on the other hand has more triangle shaped holes and is referred to as a "spoke" wheel. Take a look at…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Size Bolts Hold Fulton Spare Tire Carrier to Trailer and the Wheel to the Carrier

Continue Researching