Replacement Handle for Trailer Valet Jack TV64VR

Question

Question:

Purchased mine from Costco but was missing the hand crank, currently using the drill attachment but would be a nice option to use the hand crank.

asked by: Brian C

0

Expert Reply:

Hey Brian, we do have the replacement handle for the Trailer Valet part # TV64FR with the part # TVXLHC.

expert reply by: Jameson C

0

Jameson C.

1/19/2026

Hey Brian, did the replacement crank for your Trailer Valet jack work out as expected? Knowing how it performed could help others looking for the same option.

Answer 1

No, it's not sold separately. The 5K Trailer Valet JXS Trailer Jack item #TV64FR is only available with the mounting bracket.

view full answer...

Answer 2

The Trailer Valet #TV64FR JXS 5K trailer jack is a pipe mount swivel jack that can be removed from the trailer by pulling the pin shown in the provided photo. If you click the provided link, you can see a video showing a typical installation.

view full answer...

Answer 3

The mounting plate for the Trailer Valet JXS Trailer Jack #TV64FR has bolt holes that are separated on center 5-1/2" horizontally. The vertical mounting holes are separated on center 1" each for a total of 5" from the top hole to the…

view full answer...

Answer 4

A weld-on pipe mount is not included or available for the Trailer Valet JXS Trailer Jack w/ Footplate and Drill Powered Option - Side Mount - Sidewind - 2K #TV34FR. There isn't an option to weld on the Trailer Valet jacks, and the only…

view full answer...

Answer 5

For a jack that is similar and has a bolt-on installation I recommend the Trailer Valet JXS Trailer Jack w/ Footplate #TV64FR. This is a sidewind swivel jack with a 5,000 lb support capacity that fits a frame up to 4-3/4" tall x 3-3/4"…

view full answer...

Answer 6

The Trailer Valet JXS Trailer Jack part #TV64FR comes with a footplate only. There isn't an exact fit wheel option for this jack but there are likely other options that will work. That said, these wheels reduce the lift/support capacity of the…

view full answer...

Answer 7

Hello Michael, Happy to get the right jack for your SunTracker. I looked up the specs for the weights, the boat itself is about 3,000 pounds, the motor is around 500 pounds, then fuel, gear and batteries around 400 pounds, and the trailer itself is…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Handle for Trailer Valet Jack TV64VR

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching