Can the JR Products LED Light Be Daisy Chained and Controlled By a Switch

Question

Question:

Can these lights be mounted flush to the roof metal ribs of a trailer and daisy chained so there are multiple lights all controlled by a single switch?

asked by: Stan S

0

Expert Reply:

Yes you can, Stan. You can both daisy chain the Peterson Great White LED Trailer Interior Cove Light # 359-2, and screw them into the metal ribs on your trailer.

You can then wire the lights to a simple on/off switch like the Single Rocker Switch # 37212225.

expert reply by: Bryce D

0

Jesse M.

2/3/2026

Hey Stan, how did the setup go with the Peterson Great White LED lights and the rocker switch? It’d be great to hear if wiring them together on one switch worked as planned. Your update could make it easier for others looking to light their trailers the same way.

Answer 1

Looks like you need a continuous hinge roof vent lid like the part #BV0554-01 based on what I can see in your picture can compared to the install pictures we have of this cover.

view full answer...

Answer 2

No problem. If your existing trailer interior lights use a 1-wire hookup this means they use their mounting hardware to make the ground connection and the single lead is the +12V feed. Adding more high-efficiency LED lights with 2 wires will only…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Can the JR Products LED Light Be Daisy Chained and Controlled By a Switch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching