Bearing Kit for Dexter 3,500 lb Axle

Question

Question:

I am looking for a bearing kit for Dexter Axle P-15, Model SLR, 3500 lb. ,serial number D-4181243 1999 Ja-Mar trailer utility trailer . The spindles are 5 lug with 15 inch wheels. Will this BK2-100 kit fit or is there another kit?

asked by: Robert C

0

Expert Reply:

Hi Robert; the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle # BK2-100 is the correct bearing kit for your axle.

expert reply by: Robin H

0

Robert C.

7/24/2024

Thank you

Reply

Answer 1

Hey thanks for reaching out, Robert. Your Dexter P-15 model SLR 3,500 lb axle does use the standard bearing combination for a 3,500 lb axle. I was able to confirm this with Dexter. So, you have #L68149 for the inner bearing and #L44649 for the outer…

view full answer...

Answer 2

The standard 3,500 lb axle uses the Hub Bearing Kit #BK2-100 which is for a #84 spindle. If your axle is a 1990 or newer then you likely need these parts but if it's older then I'll need you to measure your spindle to make sure we can get you…

view full answer...

Answer 3

You are correct that is a 3,500 lb axle. If you want a bearing kit the #BK2-100 you looked at is the right one. This comes with a #L44649 outer and #L68149 inner bearing along with a #58846 (10-19) grease seal. If you want a replacement idler hub you…

view full answer...

Answer 4

The correct bearing kit for a Dexter 3,500 trailer axle is the part #BK2-100.

view full answer...

Answer 5

Hey Chris! We don't have a way of knowing which axle is on your 2017 Jayco Jay Flight 17BH but I can still help you out. If I had to guess based on the GVWR it is a 3,500 lb axle so the correct bearing kit would be the #BK2-100. If you can take a…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 8

Hey Greg, There unfortunately there isn't a guide to tell us the bearing and grease seal combination for your hub so you'll have to remove it and check the bearings/seal for their part numbers or use a digital caliper #PTW80157 to measure the…

view full answer...

Answer 9

I believe you meant a TDE 46245, is that correct? If that's the case, you've got a 3500 lb axle which uses a 10 inch hub/rotor with a 5 on 4-1/2 wheel bolt pattern. You'll want to use the Kodiak #KHR10D hub/rotor as a replacement. The hub…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Bearing Kit for Dexter 3,500 lb Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching