Can Yakima SprocketRocket Be Adapter To Fit Rhino-Rack T-Slots

Question

Question:

I have a question about attaching another t-slot system to my existing aerobar rhino that I bought from you 2 years ago I have acquired a yakima sprocket rocket and it has rack mounts for the smaller tube sizes on a smaller roof bar. As the yakima sprocket rocket has tslots i was wondering if there is a system to perpendicular mount the yakima sprocket rocket tslot to my rhino aerobar tslot. Attached are photos

asked by: Stuart M

0

Expert Reply:

Hi Stuart; I didn't get your photos but I did reach out to Yakima about this. They said that there is no way to adapt the SprocketRocket to T-slots. The only thing it will fit is square or round bars since they were the primary design when the bike rack was made.

Unfortunately, this means the only solution is to switch to a different bike rack. If you want to stick with Yakima check out the High Speed # Y25FR or # Y54NJ. These are fork-mount carriers that can clamp onto your Rhino-Rack bars or mount using the T-slots.

expert reply by: Robin H

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

Hey Ron, congratulations on the new trailer! I have a Jay Feather myself and love it. You're definitely off to a great start with a weight distribution hitch, it will make a world of difference towing that trailer with your F-150. The Weigh Safe…

view full answer...

Answer 10

For your 2024 Nissan Frontier I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR. I like the Liberty because it is simple, reliable, and looks great in any vehicle. The main unit installs behind the dash, so only the control knob will…

view full answer...

Answer 11

Hey Katja, the Curt Echo Mobile brake controller part #C51180 would be your best option. This is a wireless brake controller and all it requires is a 7-way with the taillight functions and the 12 volt accessory circuit active and you'd be set. So…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Can Yakima SprocketRocket Be Adapter To Fit Rhino-Rack T-Slots

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching