What Kind of Zerk Fitting is Used on EZ Lube Axles?
Updated 02/03/2026 | Published 07/07/2024
Products Featured in This Question
Question:
What style grease fitting (zerk) is used on the E-Z lube axle ? A screw in fitting or a drive- fitting?
asked by: Dan D
0
Expert Reply:
They're screw in. The zerk fittings on the Dexter EZ Lube Axles like item #T3584F-EZ-8974 are a 1/4" pipe thread. If you need a replacement zerk fitting you can use part item # Gzerk, which we have confirmed to fit the Dexter EZ Lube Axles.
expert reply by:
Jerred H
0
Product Page this Question was Asked From
Dexter Trailer Axle Beam with EZ-Lube Spindles - 89" Long - 3,500 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Grade
- No Hubs
- 3500 lbs
- Spindles Only
- 74 Inch Spring Center
- 89 Inch Hub Face
- No Drop or Lift
- Dexter
more information >
Continue Researching
- Search Results: carbon monoxide and propane rv gas detectors
- Shop: Replacement Grease Zerk for Ram Jacks
- Shop: Dexter Grease Zerks for E-Z Lube and Nev-R-Lube Axles - Thread-In - 1/4" OD x 5/16" Long
- Q&A: What is Speed Rating of Trailer Tires in Size 4.80-8
- Shop: Kenda K371 Bias Trailer Tire - 4.80/4.00-8 - Load Range C
- Q&A: Troubleshooting Wet Bolts/Grease Zerks That Will Not Accept Grease
- Q&A: Compatible 4.80 X 8 Trailer Tire That Can Handle Highway Speeds
- Shop: Kenda Loadstar K371 Bias Trailer Tire - 4.80/4.00-8 - Load Range B
- Shop: Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel - 5 on 4-1/2 - Load Range B
- Search Results: idler hub
- Q&A: What Type of Grease to Use for Dexter Axle Hub Assembly
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Dexter Trailer Idler Hub Assembly - 2,000-lb and 2,200-lb E-Z Lube Axles - Pre-Greased - 5 on 4-1/2
- Shop: Trailer Hitch
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Search Results: trailer jack
- Search Results: trailer lights
- Shop: Suspension Enhancement
- Search Results: trailer leaf springs
- Shop: Brake Controller
- Shop: Gooseneck Hitch
- Search Results: trailer brakes
- Shop: Base Plate for Tow Bar
- Shop: RV Interior Lighting
- Q&A: Looking for Pre-Greased 3,500 Idler Hub that is Galvanized for Trailer Axle
- Article: Trailer Wiring Diagrams
- Q&A: What Upgraded Equalizer Can I Use to Replace My 5 5/8" Long Standard Equalizer?
- Article: How to Raise Your Travel Trailer Height
- Q&A: Replacement Axle, Hubs, and Brakes for 2017 Jayco Jay Flight With Lippert Axle
Jerred H.
2/3/2026
Hey, did the screw-in zerk fitting work out for your Dexter EZ Lube axle? Knowing how it fit could help others replacing their fittings too. Your update could make it easier for the next person with the same setup.