SmartPlug 50 Amp RV Power Cord Inlet And Connector Dimensions

Question

Question:

What are the dimensions of the 50 Amp Smart plug. Thank You. Kenny

asked by: Kenny W

0

Expert Reply:

Hi Kenny,

I've drawn up a diagram of the dimensions for the SmartPlug RV Power Inlet and Connector - 50 Amp # SM66FR below. If you need any other measurements just let me know.

expert reply by: Kevin C

0

SM66FR Dimensions
(click to enlarge)

Robin H.

2/3/2026

Hey Kenny, did the diagram for the 50-amp SmartPlug give you the measurements you needed? Knowing how it worked out could help others looking for the same details.

Answer 1

The MaxxAir FanMate Rain Cover in Black #MA00-955002, smoke #MA00-955003, or white #MA00-955001 are confirmed to fit the rounded factory mounting points like you see on the attached photo. If you have the flat mounting anchor points like in the other…

view full answer...

Answer 2

The MaxxAir Vent Covers part #MA86JR and part #MA00-955003 both are just used to cover the vent to protect it from the elements. However, the MaxxAir FanMate part #MA00-955003 is designed for the high power fan models because it does allow almost…

view full answer...

Answer 3

The rattle or play you experienced is very common and the solution isn't to replace the ball mount with a tighter fitting one as that's not really possible but is to use an anti-rattle device like the part #63232. This installs in the shank…

view full answer...

Answer 4

Yes, the dimensions of the 30 Amp SmartPlug RV Power Inlet and Connector, found in Gray #SM87FR or White #SM77FR is as follows: Receptacle - 3.25" wide x 4.5" tall x 3.75" long (or deep) Plug - 3" wide x 3" tall x 4"…

view full answer...

Answer 5

It's possible that you might not have the correct version of the application, since my contact over at Hughes says there are 2 different applications and that there is an EPO version of app in app store that would be required to connect to your…

view full answer...

Answer 6

I wouldn't say one type of ball mount has more or a reputation of failing than the other. The welded on triple ball mount part #BWBMTT31004 that you referenced is very well made and would not have any issues with reliability.

view full answer...

Answer 7

You can absolutely trust the manufacturer ratings for the ball mounts we have available, regardless of whether or not they feature a solid or hollow shank. Ball mounts and other towing products are typically tested well beyond their actual listed…

view full answer...

Answer 8

That's a good question and the right RoadActive Suspension Kit for your 2020 Ford F-150 with two-wheel drive really comes down to just two things: the amount of squat you are experiencing and if you are towing, the amount of tongue weight on the…

view full answer...

Answer 9

I called our tech contact at Lippert and he said that the manual override of the older style A-frame jacks that they carry do not like to operate if the power source of the jack is active. Basically if the jack is functioning fine with the switch it…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

SmartPlug 50 Amp RV Power Cord Inlet And Connector Dimensions

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching