Wiring Diagram For A Hydrastar Electric-Over-Hydraulic Disc Brake Actuator

Question

Question:

Yes! On the disc Acturator what is exactly the wiring diagram to connect to my trailer? Not really savvy on what wire goes where! Thanks for any help in this matter! Tom,

asked by: Tom B

1

Helpful Expert Reply:

Hi Tom,

I've attached the wiring diagram for the Hydrastar Electric Over Hydraulic Actuator Kit for Disc Brakes # HBA16-252-82 below as well as a video I made where I'll walk you through the installation process.

expert reply by: Kevin C

1

HBA16-252-82 Wiring Diagram
(click to enlarge)

HBA16-252-82 wiring diagram
(click to enlarge)

Tom

6/28/2024

Thanks a bunch!! Appreciate it!!

Kevin C.

6/29/2024

@Tom My image uploader pulled the wrong diagram. I've reuploaded the wiring diagram for the # HBA16-252-82 so you can ignore the radio fuse diagram.

Answer 1

Hi Rick! Since the loaded weight of your Liberty LE10K can vary quite a bit depending on what you're hauling, I recommend the B&W Continuum Weight Distribution System #BW78FR. The Continuum is adjustable for tongue weights ranging from 600 -…

view full answer...

Answer 2

If it is a 1000 psi then it would be the Hydrastar for drum brakes. The newest one is #HBA-10 and it has different wire colors, see picture. So you know that black is 12 volt power in and white is the ground. Blue/white goes to the break away switch.…

view full answer...

Answer 3

As you can see on the attached photo, the wiring diagram for the actuator shows there can be a 25-40 amp circuit breaker in-line with the black wiring which goes from the battery's positive terminal to power the actuator. This is actually only…

view full answer...

Answer 4

Wiring connections for the Electric Over Hydraulic Brake Actuator are as follows. Yellow - Cold side of breakaway switch, The wire that goes hot when a breakaway occurs. Black - Positive connection on breakaway switch, The wire that charges the…

view full answer...

Answer 5

Attached are some photos of the typical wiring functions for truck and trailer 7-Way blade connectors, like parts #PK11893 and #PK12706. If you typical pull a trailer that has a 7-Way connector then you want to follow the pin out diagrams I…

view full answer...

Answer 6

The 4 Terminal Relay, #TR38665, will fit the 2008 and Newer Ford Escape. We have had customers state that these relays are good replacements for the ones offered from the dealer. They are designed to complete the factory tow package on several…

view full answer...

Answer 7

It sounds like your husband had to cut a hydraulic brake line to free-up your trailer's locked brakes. Causes for this kind of issue could be anything from a bad master cylinder in your actuator/coupler, to a blockage in one of the brake lines,…

view full answer...

Answer 8

Brake calipers are typically installed so they point toward the back of the trailer, but it is okay to install them pointing up or toward the front of the trailer. The important thing to consider when installing the calipers is to make sure at least…

view full answer...

Answer 9

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 10

Yes, the different Dexter Axle numbers correlate to various axle dimensions and setups. You always want to match the specs from your new axle to that of your old axle to make sure everything matches, lines up, and is able to handle the amount of…

view full answer...

Answer 11

The thickness of the tube is not any different as they are both 3 inch diameter, and the spindles are also the same utilizing the same inner diameter bearings, hubs, and seals. The difference in capacity is in the custom bend in the axle that creates…

view full answer...

Answer 12

Hey Aaron, the DeeMax Disc Brake kit part #DE28YR that you referenced is designed to attach to a brake mounting flange that is on the trailer spindle. If your trailer was missing that the correct flange for a 6k axle would be the part #4-44-1.

view full answer...

Wiring Diagram For A Hydrastar Electric-Over-Hydraulic Disc Brake Actuator

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching