Can The Dexter Brake Actuator with Manual Lockout # T63FR Be Used With Disc Brakes

Question

Question:

Can the T63FR be used for disc brakes without changing the master cylinder? Will it work without changing the master cylinder? If not then I need an actuator with a2 ball with a manual lockout for DISC brakes!

asked by: Shane S

0

Expert Reply:

Hi Shane,

The Dexter Brake Actuator with Manual Lockout # T63FR would not be able to build up enough pressure to activate your disc brakes and would require a master cylinder replacement that's compatible with disc brakes. The options we offer in this category would either come with an electric lockout and without but there unfortunately aren't any with a manual lockout option. You could go with the Demco Hydraulic Brake Actuator w/ Electric Lockout # DM62VR and use the Tow Ready 4 Pole to 5 Pole Trailer Wiring Adapter # 20036 to get the signal from the reverse lights to lockout the actuator.

expert reply by: Kevin C

0

Shane S.

6/10/2024

Can you just change out the master cylinder?

Kevin C.

6/10/2024

@ShaneS Unfortunately it doesn't look like there's a compatible replacement cylinder but Dexter does offer another actuator that we don't carry yet that is designed for disc brakes and has a manual lockout option. I'm working on getting it added to our selection and then you should be good to go.

Answer 1

Mark, the Kodiak Disc Brake Kit #K2HR35DKG appears to be what you're looking for but you're going to need to verify which bearings your trailer uses right now to make sure it's compatible. The bearings, actuator #DX29FR and brake lines…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Can The Dexter Brake Actuator with Manual Lockout # T63FR Be Used With Disc Brakes

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching