Can The InfiniteRule Trailer Coupler Lock Be Purchased In A 2pk With The Same Keys

Question

Question:

Can this Lock be re-keyed or purchased in pairs with the same key?

asked by: Ed

0

Expert Reply:

Hey Ed,

We currently only offer the InfiniteRule Trailer Coupler Lock # IR38FR in a single quantity and they would not be able to be rekeyed without paying a locksmith, which wouldn't be cost-effective. The manufacturer offers this lock in a 2pk quantity though.

expert reply by: Kevin C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Hey JD, The Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS88RR uses hitch pic lock #WS54CR, which has a shear strength capacity of 45,000lbs according to Weigh Safe.

view full answer...

Answer 5

Yes, you can so long as your Demco EZ latch coupler is cast like item #DM14040-81 or item #DM37ZR. The InfiniteRule Lock for Demco eZ-Latch Trailer Couplers item #IR66FR works great with these couplers whether they're being towed or parked.

view full answer...

Answer 6

The InfiniteRule Lock for Demco eZ-Latch #IR66FR will fit 2" and 2-5/16" couplers. This lock has an internal length of 2-15/16" to fit the pin hole on your coupler. I have linked an image below showing it on a 2-5/16" coupler in…

view full answer...

Answer 7

It sounds like your Big Tex car hauler trailer uses a collar lock coupler like the Bulldog Collar-Lok Coupler #BD028442. The most secure lock for a coupler like this will be the Blaylock Total-Encasement Coupler Lock. We have part #BLTL-23 for a…

view full answer...

Answer 8

Since the mounting holes of the Demco Coupler part #DM15931-52 are 1/2 inch in diameter you'd want to source 1/2 inch diameter bolts Grade 5 or higher. Go with bolts and nuts long enough to fit through coupler.

view full answer...

Answer 9

Your Airstream uses Dexter Torflex #10 axles. As long as the axle mounting brackets aren't the 3 inch tall high profile brackets, the Dexter #K71-707-02 lift kit for tandem axle trailers would work perfectly for you. I've linked to the…

view full answer...

Answer 10

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 11

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Can The InfiniteRule Trailer Coupler Lock Be Purchased In A 2pk With The Same Keys

Product Page this Question was Asked From

Continue Researching