Do the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems Fit HappiJac 4220 Jacks?

Question

Question:

Hello - I have HappiJac 4220 jacks. Will this swing out work on those? I cant seem to find a recommendation for them. They are mounted on a NorthStar truck camper.

asked by: Mason B

0

Expert Reply:

Yes, they will. The Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems item # LC182496 will work on the following models including the HappiJac 4220 or pn 736514 jacks:

HappiJac Electric Truck Camper Jack System - 36-1/2" Lift - 11,200 lbs item # LC736515-ELKIT

HappiJac Manual Truck Camper Jack System - 36-1/2" Lift - 11,200 lbs item # LC736515-4

HappiJac Manual Truck Camper Jack System - 34-1/2" Lift - 8,800 lbs item # LC736514-4

HappiJac Electric Truck Camper Jack System - 34-1/2" Lift - 8,800 lbs item # LC736514-ELKIT

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Do the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems Fit HappiJac 4220 Jacks?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching