Trailer Hub Grease Seal for UFP part number 07026

Question

Question:

I have a vault hub with inner seal leaking. It’s a heritage boat trailer. I believe part number is UFP 07026 1.98 x 1.38. Is the correct seal from etrailer part 13194 to maintain vault sealed system or is it BB60005? Another option, can I convert to grease filled with bearing buddy caps and use part number BB60005 or is this not recommended?

asked by: Jeff

0

Expert Reply:

Hey Jeff, based on the dimensions you took the only seal we offer that will work is the Bearing Buddy # BB60005.

Actually the Bearing Buddy seal mentioned is for grease applications so that would be the lube type you'd need use.

expert reply by: Jameson C

0

Answer 1

Based on the dimensions listed we have the bearing kit part #BB60001 which has an outer diameter of 1.980 inches and an internal diameter of 1.375 inch. You'd want to use a digital caliper like #PTW80157 to verify that your dimensions are the…

view full answer...

Answer 2

For a replacement of the NOK AB1990E grease seal you'll need the Grease Seal #13194.

view full answer...

Answer 3

Grease seal set #BB60005 has an inner diameter of 1.375 (1 3/8) and an outer diameter of 1.980. These should work for both of your trailers.

view full answer...

Answer 4

I believe you are referring to the manual for various Dexter hub assemblies that call for the application of Permatex sealant or equivalent prior to the installation of a new seal. While I don't recommend going against the manufacturer's…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Trailer Hub Grease Seal for UFP part number 07026

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching