Replacement Trailer Hub Grease Seal with Outer Diameter 2 inch and Inner Diameter 1-3/8 inch

Question

Question:

I need two seals for my boat trailor bearings. The inside diameter is 1 3/8 and the outside is 2.00.

asked by: John G

0

Expert Reply:

Based on the dimensions listed we have the bearing kit part # BB60001 which has an outer diameter of 1.980 inches and an internal diameter of 1.375 inch. You'd want to use a digital caliper like # PTW80157 to verify that your dimensions are the same since the dimensions have to be exact.

expert reply by: Jameson C

0

Answer 1

Grease seal set #BB60005 has an inner diameter of 1.375 (1 3/8) and an outer diameter of 1.980. These should work for both of your trailers.

view full answer...

Answer 2

Hey Jeff, based on the dimensions you took the only seal we offer that will work is the Bearing Buddy #BB60005. Actually the Bearing Buddy seal mentioned is for grease applications so that would be the lube type you'd need use.

view full answer...

Answer 3

For a replacement of the NOK AB1990E grease seal you'll need the Grease Seal #13194.

view full answer...

Answer 4

For your Dico Hub 45263, you are going to want to use part #L44649 for both the inner/outer bearings and part #168255TB for the grease seal which has a double lip. I was not able to confirm that the hub uses different inner and outer bearings. We had…

view full answer...

Answer 5

We've had customers with your Dico 45263 hub in the past get us their bearing numbers so we know that for a replacement with the wheel bolt pattern you need you could use the #AKIHUB-545-2-G-EZ-2K and you'd be set.

view full answer...

Answer 6

I was able to get a hold of Pacific Boat Trailers and find out which bearings and seals you would need, but unfortunately the seal that is used on a Dico 45263 hub is different than standard 5 on 4-1/2 hubs that use the bearing numbers they gave me.…

view full answer...

Answer 7

For your ST175/80D13C tires, the D means that they are diagonal internal construction more commonly referred to as bias ply tires. The cords run at a 32 degree angle versus radial tires which run at 90 degrees. The C in that location used to signify…

view full answer...

Answer 8

Thanks for the picture! If you can't get your races out, you'll just need the entire new hub assembly #AKIHUB-545-2-EZ-2K which comes with brand new races already installed, new bearings, and new grease seals but you'll need to use #34823…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Trailer Hub Grease Seal with Outer Diameter 2 inch and Inner Diameter 1-3/8 inch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching