Which Way Should 2-Piece Polypropylene Trailer Vent be Placed
Updated 04/28/2014 | Published 04/27/2014
Question:
looking at part # WHMAV2-WAVT2 to vent an enclosed fiberglass Triton snowmobile trailer. Which way is the venting part of the exterior piece supposed to face? ive seen them installed forward, backward and down. Facing forward would provide the most amount of airflow while driving, but it also seems like it would possibly be too much. I dont want a hurricane inside the trailer when Im doing 70mph. What about location? Best to have one towards top and bottom? Or both towards the top?
asked by: Scott
Expert Reply:
If it were me I would install the trailer vent # WHMAV2-WAVT2 with the fins angled down to reduce the amount of rain that could fall into the vent.
Having it at the front of the trailer should be fine since the tow vehicle is going to act as a screen for a large portion of the wind. Also, most trailer tires are not rated for speeds over 65 miles per hour so you will want to keep an eye on that!
If you want air flow-through then you would want one vent at the front and another at the back. I would have them both angled down.
Product Page this Question was Asked From
2-Piece Exterior Wall Vent for Enclosed Trailers - Polypropylene - 3" Diameter Hole - White
- RV Vents and Fans
- Vent
- Wall Vent
- No Fan
- Plastic
- White
- Redline
more information >
Continue Researching
- Search Results: seaflo 42 series
- Search Results: pumps rv fresh water
- Shop: Seaflo Diaphragm Pump for Boats and RVs - Variable Flow - 3 GPM - 55 psi - 12V DC
- Video: Replacement Round Interior Trailer Vent for 3" Diameter Hole: The Breakdown
- Shop: 2-Piece Exterior Wall Vent for Enclosed Trailers - Polypropylene - 3" Diameter Hole - Black
- Shop: Seaflo Diaphragm Pump for Boats and RVs - Open Flow - 5 GPM - 60 psi - 12V DC
- Video: Breaking Down the 2-Piece Exterior Wall Vent for Enclosed Trailers
- Q&A: Do Half Moon Trailer Vents Need to be Installed Facing Down or Back
- Shop: 2-Piece Exterior Wall Vent for Enclosed Trailers - Polypropylene - 3" Diameter Hole - White
- Q&A: Best Mounting Orientation of WAVT2-WHMAV2 2-Piece Polypropylene Trailer Vent
- Video: The Low-Down on the Replacement Exterior Half-Moon Trailer Vent for 3" Diameter Hole
- Search Results: trailer wall vent
- Search Results: enclosed trailer vents
- Shop: Replacement Exterior Half-Moon Trailer Vent for 3" Diameter Hole - Black
- Q&A: Attaching the Redline 2-Piece Roof Vent to the Front Side of a Cargo Trailer
- Q&A: Side Wall Vent Recommendation for an Enclosed Trailer for Maximum Air Flow
- Article: Performance Chips and Modules
- Search Results: side vent
- Q&A: Picking Out Replacement Roof Vent Lid for Keystone Laredo
- Q&A: How Should the 2-Piece Polypropylene Trailer Vent be Positioned when Installing
- Video: Edge Insight CS2 Comprehensive Gauge Display: The Breakdown
- Video: Comprehensive Review: Mushroom Vent
- Video: All About the WeatherTech Side Window Air Deflectors with Dark Tinting
- Shop: Nerf Bars - Running Boards
- Shop: Performance Chip Tuners
- Shop: Suspension Enhancement
- Shop: Van Cargo Mat
- Shop: Roof Rack
- Shop: Mushroom Vent - Black
- Shop: Edge Insight CS2 Comprehensive Gauge Display - Color Screen
on RV Vents and Fans
