Replacement Axle

Question

Question:

Hi there, trying to get a replacment axle for a Alcom trailer with Dexter Axles. 3500 lbs single. Dexter preconfig 4233825 Engraved model D35 SC/OB 69, HF 86 Tube cut: 74.25 Cone bearing I have a picture of the axle tag and trailer info if needed. Thanks Mike 847-814-6871

asked by: Michael T

0

Expert Reply:

Thank you for the extremely detailed information! Sorry Michael but we do not have any axles with those specifications. The closest one we have available is the 5,200 lbs Dexter Trailer Axle Beam item # 8327816. It has a 86-1/2" hub face and a 71-1/2" spring center.

expert reply by: Jerred H

0

Answer 1

Hey Matt, There are a couple ways you can still identify the weight rating of your axle if you can't find any info on the frame or on the axle itself. The first is to simply take a quick measurement of the axle's tube diameter. Almost always,…

view full answer...

Answer 2

There are a few troubleshooting steps that you can run through to determine why your running lights are not working. The first step that I would take is to check all of your ground connections. A faulty ground connections can cause many different…

view full answer...

Answer 3

Thank you for the information James. The closest axle we have for those dimensions is the 5,200 lbs Dexter Trailer Axle Beam item #8327816. It has a 86-1/2" hub face and a 71-1/2" spring center. The item #8327816 axle would stick out an…

view full answer...

Answer 4

The right and left orientation is determined if you are standing behind the trailer looking towards the tow vehicle. The left side is the drivers side and the right side is the passengers side. Tthe shorter brake pad will always be in the front of…

view full answer...

Answer 5

The left side is the driver side, right side is passenger side. On a trailer brake assembly like #23-105 the arm that the magnet is on points to the front of the trailer and the magnet always will be on the bottom. I have included a picture that…

view full answer...

Answer 6

I went out to the warehouse and grabbed a 7-Way Molded Trailer Wire Connector #H20046 to measure it for you. I used a set of digital calipers to get an accurate measurement. The diameter of the outer black sheath is 0.59 inches or 19/32 of an inch. A…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Axle

Product Page this Question was Asked From

Continue Researching