Fan to Replace MaxxAir That Doesn't Have Replacement Motor

Question

Question:

Im needing a fan motor replacement or compatable to a fan motor 10-03817z. dont think you make any more, in a mini maxx model 3852 fan.

asked by: Tony M

0

Expert Reply:

We don't make these parts, we just sell them, though I can tell you the 10-03817z is not something available. The best we can offer is a new vent like the MaxxAir Mini Manual RV Roof Vent # MA00-03700.

I have added a link below to our entire selection of roof vents.

expert reply by: Kyle S

0

Answer 1

I would be happy to help! Since your brake assembly is stamped K23-462-00 you will want to go with the Dexter Electric Brake Assembly for 4.4K Axles #K23-462-00 and you can confirm that this is the correct assembly and not just an incorrect sticker…

view full answer...

Answer 2

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 3

The Dexter Nev-R-Adjust Electric Trailer Brake Assembly equivalent to your current assemblies is part #K23-478-00 for the left and part #K23-479-00 for the right side. Please check the mounting pattern of your current assemblies to the #K23-478-00…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Fan to Replace MaxxAir That Doesn't Have Replacement Motor

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching