Hub Seals for Lippert 4,400 lb Axles

Question

Question:

Hello, I am looking for axle seals for my Lippert 4400lb axles. The Lippert Model for the axles is V000531456. The Serial for the axles are S009669741 and S009669740

asked by: Doug

0

Expert Reply:

Hey Doug, the grease seal you'd need for your Lippert 4,400 lb axles is the part # RG06-050 for a pair or part # 58846 for a single seal.

expert reply by: Jameson C

0

Answer 1

The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 or just the Grease Seal part #RG06-050.

view full answer...

Answer 2

Hi Sergio! I don't know why they do this, but Lionshead is pretty notorious for discontinuing their wheel designs. The Bobcat happens to be one of those, unfortunately. It is one that we used to carry, so I have a good idea of what it looks like…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Hub Seals for Lippert 4,400 lb Axles

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching