Possible Replacement Grease Seal Recommendation for a Shorelandr Trailer Using a 174253TB Seal

Question

Question:

I can’t find a replacement wheel bearing seal for my Shorelandr trailer TCM 174253 TB any ideas?

asked by: Steve

0

Expert Reply:

This has come up before and we've had customers in the past use the Grease Seal # RG06-050 to replace their 174253TB grease seal.

You're going to want to take a set of digital calipers and measure the inner and outer diameter, and if the inner is 1.719" and the outer is 2.565" then you could use this seal as a replacement.

expert reply by: Bryce D

0

Answer 1

Thanks for the picture and your patience! I did some research and made some phone calls, the correct replacement for your actuator is the Replacement Inner Member for Dexter DX7.5L Actuator - Single Axle w/ Disc - 2" Ball - 7,500 lbs item…

view full answer...

Answer 2

Hi Charles, While we don't currently offer the inner member that you're needing for the UFP A-70 we do offer a compatible replacement with the Dexter DX7.5L A-60 Brake Actuator #DX33FR. This is the entire actuator assembly along with the…

view full answer...

Answer 3

Thanks for the pictures Brian. Yes, you are correct the Replacement Inner Member for Dexter DX7.5L Actuator item #DX99FR will replace your UFP A-70 surge brake actuator. The A-"number" was for the weight capacity of the coupler; an A-60 was…

view full answer...

Answer 4

The hub your Shorelandr boat trailer has is part number 4470400 which is a 3,500 lb axle hub. So for a replacement surge brake assembly you'd want the part #AKUBRK-35 for a set of left and right hand assemblies.

view full answer...

Answer 5

If the inner diameter is 1.719 inches and the outer diameter is 2.565 the #RG06-050 would be the closest matching grease seal we offer. You will need a digital or dial caliper for this measurement. The grease seal number you referenced doesn't…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Possible Replacement Grease Seal Recommendation for a Shorelandr Trailer Using a 174253TB Seal

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching