Will InfiniteRule Lock for Demco eZ-Latch Trailer Couplers Fit Demco EZ Latch Gooseneck Coupler

Question

Question:

Will this lock work on the gooseneck version of the Demco ez latch?

asked by: Brandon

0

Demco EZ Latch Gooseneck Coupler
(click to enlarge)

Expert Reply:

Yes, the InfiniteRule Lock for Demco eZ-Latch Trailer Couplers # IR66FR will fit your Demco EZ Latch gooseneck coupler.

expert reply by: Robin H

0

Answer 1

For the Demco EZ Latch Coupler like item #DM37ZR that does not have a lip around it you would want the Fastway Universal Trailer Coupler Lock item #DT25013KA. This is by far the best and most compatible option of the ones you listed. If you have more…

view full answer...

Answer 2

There is indeed a pin lock for the Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball #DM37ZR. In fact, there is one made specifically for this coupler, from InfiniteRule: - InfiniteRule Lock for Demco eZ-Latch Trailer Couplers #IR66FR…

view full answer...

Answer 3

Hey Scott, thanks for reaching out! The length of safety chain will kind of depend on the length of your ball mount, but as a general rule of thumb you can use the 60" Curt Safety Chains with Latching Hooks #C19749 with the 10K Demco Cast Head…

view full answer...

Answer 4

You just need to pack the bearings on hub and drum assembly #8-276-5. There's no such thing as too much grease for bearings! If it is an EZ lube hub with a grease zerk fitting at the end of the spindle you will know there is enough grease once it…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Will InfiniteRule Lock for Demco eZ-Latch Trailer Couplers Fit Demco EZ Latch Gooseneck Coupler

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching