Can Automatic On/Off Switch For Compartment Light Work on Cargo Bay Doors

Question

Question:

The cargo bay doors on my 2018 Canyon Star open horizontally with a gas spring mounted at the bottom of the door. Could these switches work with this application?

asked by: Chuck F

0

Expert Reply:

Sure, I can't see any reason why the Automatic On/Off Switch for RV Compartment Light - Strut Mount - 42" Wire Leads # DG52479VP couldn't work with your cargo bay doors. So long as you have 6 mm, 8 mm, 10 mm, or 12 mm gas strut rods it should work just fine.

expert reply by: Kyle S

0

Answer 1

I recommend using the Magnetic Door Sensor #LC374198 for your custom boat project. These sensors are safe to be used in wet conditions and being magnetic will allow you to place the wired sensor on either the door or frame where you plan to mount the…

view full answer...

Answer 2

The switch inside the Diamond Group #DG52479VP housing is marked 3a @ 30 VDC. The connector wires are marked 22 AWG and are probably rated around .9a @ 300 volts. Wire capacity will change as runs to power supple lengthen.

view full answer...

Answer 3

The Automatic On/Off Switch for RV Compartment Light part #DG52479VP must be installed using a 12 volt hardwired light that attaches directly to a battery as this is how the switch can interrupt and apply power to the light. The Optronics LED RV…

view full answer...

Answer 4

The Leer 100XR isn't specifically listed by Pop and Lock but more than likely the #PAL9772 will fit. It requires a frameless, bonded glass door with a 1-1/8" center hole for a rotary latch. This particular kit would upgrade your existing…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Can Automatic On/Off Switch For Compartment Light Work on Cargo Bay Doors

Product Page this Question was Asked From

Continue Researching