Replacement Hydraulic Drum Brake Assembly Recommendation to Replace Rusty Assemblies
Updated 04/16/2014 | Published 04/15/2014
Products Featured in This Question
Question:
Do you carry the brake pads and hydraulic plungers for this set up? I will need two plungers and a set of brakes. If not, do you know the part numbers?
asked by: Geoff N
Expert Reply:
For the price of replacement brake pads and shoes it's almost always a better solution to go ahead and just replace the entire brake assembly. And in your situation with the current condition of your assemblies I would strongly recommend you do that based on how much rust is there.
In order to pick out assemblies you need to know the diameter of the assemblies and the width of the brake brake pads. I can tell by the pics you have the standard 4 bolt mounting flange. The most common brake assembly size that has the 4 bolt mounting flange is the 10 x 2-1/4 inch assemblies. If that is what you have you could use the part # 40716 for the left hand side and part # 40715 for the right had side.
These assemblies are galvanized to help fight corrosion.
If you have a different size feel free to email me back and I will help you pick out the correct assemblies.
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub with Drum
- Standard
- L68149 / L44649
- Marine Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Continue Researching
- Search Results: grease
- Search Results: l44649
- Search Results: l68149
- Search Results: marine grade trailer hubs and drums
- Video: Dexter Trailer Hub and Drum Assembly Review
- Video: Complete Breakdown of the Dexter Trailer Hub and Drum for 3,500-lb Axles
- Shop: Dexter Trailer Hub and Drum Assembly - 3,500-lb E-Z Lube Axles - 10" - 5 on 4-1/2 - Galvanized
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Dexter Multi-Purpose Lithium Grease - 14 oz. Cartridge
- Shop: Replacement Trailer Hub Bearing - L44649
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Video: Measuring To Choose The Right Trailer Axle
- Shop: Trailer Wiring
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer jack
- Shop: Suspension Enhancement
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Shop: Brake Controller
- Video: In-Depth Review of the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Hubs and Drums
