What Motor Does The Lippert Landing Gear # LC712690 Use?

Question

Question:

What motor does this set up use? Same year, make and model as the unit described

asked by: Glenn S

0

Expert Reply:

The Lippert Landing Gear # LC712690 uses the Motor # LC142178. We also have the motor with the wiring kit # LC217884 if you need to replace the wiring as well.

expert reply by: Bud M

0

Answer 1

The MB Sturgis Propane Adapter Hose - 3/8" Male NPT x 1/2" Female Flare Swivel uses a 3/8" fitting on the regulator side and 1/2" fitting on the manifold side. These are nominal fitting sizes so they don't actually measure…

view full answer...

Answer 2

To replace your current 125340 motor, you will need the #LG-142178. This will be a direct replacement for your current motor, but you may consider replacing the gear box as well. For that you will need the #LG-179015. These together should get…

view full answer...

Answer 3

For the Lippert Components Standard 5th-Wheel Landing Gear Motor w/ IP Rated Switch and Harness #LC217884, which is for LCI Power Landing Gear, you can use the Replacement Aluminum Gearbox #LG-179015 which is compatible with most landing gear,…

view full answer...

Answer 4

It's possible the 25 amp inline fuse of the Kwikee step switch part #LC371010 is blown and that's why you are seeing it no work properly. If you check out the diagram I attached you can also check to make sure the switch has all of the wires…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What Motor Does The Lippert Landing Gear # LC712690 Use?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching