How to Install a Brake Controller in a 1997 International 4900

Question

Question:

I need too know if there is a plug for installing in a 1997 International, if there isnt, I need to know how to wire it.

asked by: Tina C

0

Expert Reply:

You will need to hardwire the Pilot Brake Controller # 80550 in your 19997 International 4900 as there isn't a brake controller port. To do that check out the FAQ article I attached on installing a brake controller from scratch on a vehicle.

Basically the blue wire of the controller will get run to the brake output circuit of your trailer connector, the black wire will run to the positive side of your batter through a circuit breaker like part # 38630.

The white wire will run to the negative side of your battery and the red wire will run to the stoplight circuit. Typically this circuit can be found near the brake pedal for the brake light switch. You will want to use a circuit that only sees voltage when the brakes are applied.

Check out the FAQ article I attached for more info.

expert reply by: Jameson C

0

Answer 1

We can get your International 4900 set up with a 7-way and brake controller, and to do that you'll need to start with a 4-way, which will activate your trailer's lighting functions, and you'll then plug that into the 7-way. For the…

view full answer...

Answer 2

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

How to Install a Brake Controller in a 1997 International 4900

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching