Recommended Pace Edwards UltraGroove Tonneau Cover For A 2022 Ram 3500 6.5' Bed W/O Ram Boxes

Question

Question:

Hello, Do you think the Pace Edwards UltraGroove Retractable Hard Tonneau cover would work on a 2022 RAM 3500 six and a half bed without RamBoxes. Also there is a BW Companion fifth wheel hitch. Thanks so much.

asked by: Hope W

0

Expert Reply:

Yes, there are currently three UltraGroove covers that are confirmed to fit your 2022 Ram 3500 with a 6.5' bed and no Ram Boxes. The first two are part # 311-KRD7833 (aluminum and vinyl) and # 311-KMD7833 (aluminum). They are both matte black manual-use covers with the only difference that the # 311-KRD7833 is a mix of aluminum and vinyl while the # 311-KMD7833 is all aluminum. If you want to be able to open and close your cover with a switch or key fob instead of having to manually open/close the cover then you'll want part # 311-KED7833 instead. This option is also matte black and all aluminum.

Each of these covers sit right at the top of the bedrails so you shouldn't have any clearance issues as long as your Companion sits below the top of the bedrails.

expert reply by: Kevin C

0

Answer 1

Hello Al, thanks for reaching out. Both of the tonneau covers you mentioned, the Pace Edwards UltraGroove #311-KMD7936 and the RetraxPRO XR #RTT-80233 are a fit for your 2026 Ram 3500 with the 8' bed. There are a few noteworthy differences…

view full answer...

Answer 2

Hi Jamie! I have had a Pace Edwards Switchblade on my Silverado for 5 years now and it has seen some pretty serious ice and snow (just about a foot, once). It held all that without issue and once I cleaned it all off, it opened and closed just fine.…

view full answer...

Answer 3

The Pace Edwards UltraGroove Metal Retractable Hard Tonneau Cover - Aluminum - Matte Black Item #Item #311-KMD7833 and the Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover w Explorer Series Rails - Aluminum Item #311-FED7833 for the…

view full answer...

Answer 4

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 5

Hey John, thanks for reaching out! The Retrax Replacement Canister Drain Tubes #RE64FR have the same diameter as the Pace Edwards Replacement Canister Drain Tubes #PE55TJ so they are interchangeable, but when I went and checked them out, the Pace…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 12

Hi Fred! The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F24XV will indeed fit your 2025 Ram 2500 with the factory puck system. The only vehicles it won't fit are ones that have the factory…

view full answer...

Recommended Pace Edwards UltraGroove Tonneau Cover For A 2022 Ram 3500 6.5' Bed W/O Ram Boxes

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching