Replacement Actuator Recommendation for Discontinued Atwood 85738

Question

Question:

im looking for a replacement actuator. the actuator number im trying to replace is an atwood 85738 rated for 5,000 lbs. would you guys have anything to replace that because they no longer make them. thanks in advancde

asked by: Steve

0

Expert Reply:

Thank you for the photos!

To replace your Atwood 85738 actuator I recommend checking out the Demco 7K actuator which comes configured for Drum Brakes # DM72VR as well as Disc Brakes # DM62VR and a 2" hitch ball.

This system is a bolt on installation but an experienced welder would be able to cut off your current actuator and weld either one of these on in it's place.

expert reply by: Jon G

0

Atwood 85738 Overhead View
(click to enlarge)

Atwood 85738 Back View
(click to enlarge)

Answer 1

We no longer carry the Atwood master cylinder you are looking for so your best option would be to replace the coupler. The coupler you have is the most problematic one we see by far so going to a better design will be your best long term solution. To…

view full answer...

Answer 2

Based on the replacement numbers you mentioned, you have an Atwood part number 82541. To replace it I recommend the Titan, part #T63FR. It has a higher capacity at 7,500 pounds and still fits a 2 inch hitch ball. It's also a bolt on and includes…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

I have a complete replacement surge brake actuator option for you, but there is not a replacement master cylinder compatible with the Atwood 82541 actuator on your trailer. When Atwood went out of business all of the replacement parts were…

view full answer...

Answer 5

The Replacement Master Cylinder Assembly #T4395100 will not work to replace your Atwood master cylinder model 85841. Since replacement parts for your actuator are obsolete, your only option is to replace the entire actuator assembly. The Demco…

view full answer...

Answer 6

The Demco #DM72VR you installed is not designed to have any sort of manual lockout or bolt to hold it together, so I would not recommend doing that as you could potentially damage the coupler and render it unusable. The better option is installing a…

view full answer...

Answer 7

The Demco #DM72VR Hydraulic Trailer Brake Actuating Coupler would require four 1/2 x 4-1/2 inch grade 5 bolts to install it on a trailer tongue. I've linked to a product description video as well as a photo with the bolt spacing that you might…

view full answer...

Answer 8

Atwood Mobile Products was sold several years ago and parts for their braking systems are no longer available, but I do have a solution for you. Your 2006 Dorsey Trailer (23' Chaparral Model) has a GVWR of 7100 pounds. You can replace the surge…

view full answer...

Answer 9

Atwood master cylinders 85736 and 85841 that you referenced have been discontinued when Atwood was bought out and there aren't direct replacement parts that are compatible. I recommend replacing your 6,000 lb brake actuating coupler with the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement Actuator Recommendation for Discontinued Atwood 85738

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching