Does Longer Weight Distribution Shank Lower Weight Capacities

Question

Question:

Will using the longer shank for weight distribution system reduce the towing capacity of the tow vehicle?

asked by: Morris D

0

Expert Reply:

While longer weight distribution shanks like the Equal-i-zer part # EQ90-02-4600 do put more leverage on the hitch they do not lower the hitch's weight capacities.

expert reply by: Jameson C

0

Answer 1

I assume you want to lower your tailgate with the trailer hooked up? If that's the case, I don't recommend a hitch extension as they reduce capacity and add another failure point. That said, what you can do is switch to a longer weight…

view full answer...

Answer 2

The extra long Equal-i-zer shank #EQ90-02-4600 will not affect your trailer towing rating since this is part of a weight distribution (WD) system and it has a tongue weight (TW) range of 600 lbs - 1,400 lbs. Please note that this is labeled as an…

view full answer...

Answer 3

Swapping out the shank of your Equal-i-zer WDH with a larger 18" shank would push the trailer back an additional 6" for more clearance but there's no way for me to confirm that your trailer would completely clear the tail lights on your…

view full answer...

Answer 4

The 600 to 1,400 lbs tongue weight rating of the Equal-i-zer Weight Distribution Shank part #EQ90-02-4600 is based off of what system this shank will work with. If your Equal-i-zer Weight Distribution system is rated for 600 to 1,400 lbs the bolt…

view full answer...

Answer 5

Using a longer shank like the #EQ90-02-4600 will not reduce the capacity of your hitch. It is typically only when you use an adapter or extender like #C45791. Adding in the extra piece is what causes the reduction because of the way force is applied.…

view full answer...

Answer 6

Sounds like you are using a hitch extender with a weight distribution system. Some extenders can be used with a WD system but nearly all of them are not rated for it so it's not a good idea at all. Your best bet for gaining clearance between your…

view full answer...

Answer 7

Using the extra long Equal-i-zer Weight Dist Shank #EQ90-02-4600 referenced in your question will be your best option for gaining clearance between your truck's tailgate and jack/weight distribution system. The shank has an overall length of 18…

view full answer...

Answer 8

A longer weight distribution shank like part #EQ90-02-4600 does not require you to change your weight distribution spring bar tension at all. As long as you can still tow the trailer level with it no changes would be need. You'd just gain the…

view full answer...

Answer 9

The Blue Ox SwayPro Weight Distribution Shank, part #BXW4003, that you mentioned is in fact the longest shank (at 12") offered by Blue Ox. However, weight distribution shanks are basically the same among the different manufacturers, so you can…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Does Longer Weight Distribution Shank Lower Weight Capacities

Product Page this Question was Asked From

Continue Researching