Replacement Tonneau Cover for 2010 Toyota Tacoma Extang Trifecta

Question

Question:

I have a 2010 Toyota Tacoma with an Extang Trifecta model 44915. I need to replace the tarp only. I believe the part # is 43915. This is the 1.0inch version not the currect 2.0inch cover. Any chance you have the tarp only and/or can point to someone who does? Thank you,

asked by: Dennis B

0

Expert Reply:

We used to carry the replacement tarp you need as our part number EX43915A but we stopped being able to get it so the only solution we have would be to go with a new cover altogether with the 2.0 Trifecta that fits your truck part # EX92915.

expert reply by: Jameson C

0

Answer 1

The discontinued Extang Trifecta Soft Folding Tonneau Cover 44801 does fit a 2008 Toyota Tundra Short bed like yours so as long as that is the cover you have installed, the Replacement Tarp #EX33FR is the correct replacement. If you find you have a…

view full answer...

Answer 2

The correct replacement tarp for your Extang Trifecta Tonneau cover model 44801 is the Replacement Tarp for Extang Trifecta Soft Folding Tonneau Cover #EX33FR.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Tonneau Cover for 2010 Toyota Tacoma Extang Trifecta

Products Featured in This Question

Continue Researching