Lippert Angled Bracket Dimensions for Bracing Spring Hangers

Question

Question:

Do you sell Lippert “v” braces for strengthening spring hangers and Heavy MoRyde upgrade for CRE3000 spring equalizer. I’ve talked to George in the past. Grand Design 310 GK 2021 7000# Dexter Axles CRE3000 Equalizers I realize the “v” braces have to be welded on.

asked by: Ralph H

0

Expert Reply:

We actually don't have the angled brace from Lippert because it's been discontinued for quite a while. It looks like it's just a piece of angled steel, so you don't have to use the one Lippert made and could just make it yourself.

I've included the dimensions of the piece you're looking for so you could re-create it if you choose to do so.

expert reply by: Bryce D

0

Bracket Specs
(click to enlarge)

Bracket Dimensions
(click to enlarge)

Answer 1

To determine which MORryde Premium Rubber Suspension Kit fits your 2020 Forest River Wildwood 27RKSS you will have to measure your wheelbase. To determine your wheelbase, measure the distance between the center of your front wheel to the center of…

view full answer...

Answer 2

The instructions for the SumoSprings kit part #TSS-106-40 do not specify whether they should install in front of or behind the rear axle but I would recommend in front of the axle since most shock is going to be first on the front portion of the axle…

view full answer...

Answer 3

Hello Mike, thanks for reaching out. I see you already have the kit on order, but I wanted to make sure your question was answered. When Installing the #TSS-106-40 Sumo Springs on a tandem axle trailer, the helper springs will get installed in the…

view full answer...

Answer 4

Hello Jacques, thanks for reaching out. Yes, you can put just one MORryde X-Factor Crossmember #MR33WR on the center hanger for starter. MORryde does recommend doing all 3 for optimal support, but it is perfectly acceptable to start with just one as…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Lippert Angled Bracket Dimensions for Bracing Spring Hangers

Product Page this Question was Asked From

Continue Researching