Is the H-Channel for Enclosed Trailers Available in Different Sizes?

Question

Question:

I have this part in my cart now but i need the same part in 3/4 wide. Do you have a part number for this? H-Channel for Enclosed Trailer - 93-1/2 Long x 2 Tall x 1-1/8 Deep - Aluminum - 36281-955

asked by: Dave F

0

Expert Reply:

The H-Channel # 36281-955(93-1/2 Long x 2 Tall x 1-1/8 Deep) you found is the only size H-Channel we currently carry.

expert reply by: Bud M

0

Answer 1

I do have an option for you but we only offer the H-Channel for Enclosed Trailers part #36281-955 is one size, 93-1/2" long x 2" tall x 1-1/8" deep. That said, we do offer a C-Channel for Enclosed Trailers in 93-1/2" long x…

view full answer...

Answer 2

I checked with TRC and they sent me the following pictures for the Flat Rub Rail Trim for Enclosed Trailer #36286-955 that you referenced.

view full answer...

Answer 3

The closest we have to match those measurements is going to be the H-Channel for Enclosed Trailer #36281-955 which has an internal width of 1.027" and a height of 2". We do also have a C-Channel #362213-955 which has an inside measurement…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Is the H-Channel for Enclosed Trailers Available in Different Sizes?

Product Page this Question was Asked From

Continue Researching