Where to Weld Tandem Axle Trailer Fenders w/ Backing Plates

Question

Question:

If the backing plate isn't supposed to be welded to the trailer then how do I weld this?

asked by: Cathy

0

Expert Reply:

There is a flange on the Tandem Axle Trailer Fenders w/ Backing Plates # HP82VR that overlaps the backing plate that you'll use for the welding surface.

When it comes to welding, we always recommend having this done by an experienced welder.

expert reply by: Jon G

0

Answer 1

Yes you certainly can. In order to bolt-on a set of metal weld-on fenders such as the Single Axle Trailer Fender part #HP29VR you will need a set of mounting brackets such as the Mounting Brackets for Trailer Fender part #CE26098G-2. If you do not…

view full answer...

Answer 2

Since your trailer uses a combined wiring system where the stop and turn signals run on the same circuit, in order to add a third brake light to your trailer you would need to use a 2-Wire to 3-Wire Converter, like part #118158. This will convert the…

view full answer...

Answer 3

The lock I recommend for the Demco A-Frame EZ Latch Coupler #DM14793-81 is the etrailer Trailer Coupler Lock #e98887. This lock is going to do a great job of keeping your trailer safe and sound and will work perfectly with the Demco latch.

view full answer...

Answer 4

Hey Nathan, thanks for reaching out! I can definitely help you get setup with replacement brakes and hubs, but we don't have an all-encompassing kit that includes everything. For brakes we have the Dexter Electric Trailer Brakes #23-26-27 as…

view full answer...

Answer 5

Okay let's get started here with the suspension for your 2012 Skyline Koala 27CDS with 3,500 lb Axles; for the first part regarding your equalizers and suspension upgrade kit, so long as your current equalizer is spaced 6 inches (or close to it -…

view full answer...

Answer 6

Yes, the 15" Vesper Steel Modular Trailer Wheel #MX34FR can handle up to 65 psi. If you check out the Provider ST205/75R15 Radial Trailer Tire w/ 15" Vesper Black Mod Wheel #MX47FR (which is a Load Range D) you'll see that the same…

view full answer...

Answer 7

Hey George, the closest option we have would be the Tandem Axle Trailer Fenders w/ Backing Plates #HP82VR that you referenced which are 9 inches wide and 72 inches long. These are intended for 15 and 16 inch diameter wheels like what you have as…

view full answer...

Answer 8

Hello Lance, thanks for reaching out. When replacing shackle straps and equalizers, the replacement parts must be identical in size to the original. Since your current shackles are 3.5" long, you will NOT be able to use the 2-1/4" shackles…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 11

Hey James, I can definitely point you in the right direction. As you probably noticed, there are a ton of different bearing sizes out there for trailers. There are two good ways to determine which one will be correct for your trailer. The best way is…

view full answer...

Answer 12

We carry grease caps that fit a 2.08 diameter hub bore. Unfortunately, we do not carry dust caps with that diameter. The grease caps I recommend are Bearing Buddy, part #BB2080SS for non threaded hubs, and part #BB2080T-SS for hub bores that are 2.08…

view full answer...

Where to Weld Tandem Axle Trailer Fenders w/ Backing Plates

Product Page this Question was Asked From

Continue Researching