Replacement Wheel Bearings and Grease Seal For Lippert LCI35 Axle Under 2018 Jayco Jay Flight SLX 14

Question

Question:

I have a 2017 jayco flight slx 145 RB with a 3000 lbs Lippert Axle 866-524-7821, PN 0262995, V000269809, LC135-SB-77.5-59.5-NOSP-US-G-545-7242-18PT-CAP 300# . I want to replace the wheel bearings, can you provide part numbers of the parts you suggest to be replaced.

asked by: Kc C

0

Expert Reply:

You will need the Bearing Kit # BK2-100 for each hub on your 2017 Jayco Jay Flight SLX 145RB travel trailer. This kit includes new races, bearings, and a grease seal for one of the hubs on your Lippert LCI35 axle.

We do have the Seal Puller # PTW1219 and Install Kit # PTW83020 along with some Grease # L11390 and a Bearing Packer # ALL647646 to fill the bearings.

expert reply by: Bud M

0

Answer 1

Thank you for providing your axle tag and the tag for the brakes on your pop up camper Hector. You are going to need the Bearing Kit #BK2-100 or Timken Bearing Kit #TMK52VR should you want the higher quality bearings. Each kit is for one hub so you…

view full answer...

Answer 2

A Lippert 3,000 Lb (LCI35) Trailer Axle will use the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle part #BK2-100 which has everything you need from the bearings to the seals.

view full answer...

Answer 3

To replace the bearings on a Lippert 3,500 lbs axle you will need the outer bearing item #L44649 inner bearing item #L68149. We do have a kit that has the necessary races, seals, and bearings. It is the Hub Bearing Kit for Lippert, Dexter, and Al-Ko…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

Hey Greg, we have just what you are looking for with the CE Smith idler hub part #CE13515. This is a pre-greased 3,500 lb axle hub that is galvanized like you are looking for. What trailer is this going on?

view full answer...

Answer 12

Thanks for letting us help Michael. For the leaf springs, I'd recommend the 4-Leaf Double-Eye Spring #e54SR. This is a 25-1/4-inch double-eye spring that's a great fit for your 3,500-lb axle. If you haven't already planned on it, I'd…

view full answer...