Is Charge Controller of WF-8955PEC Lithium Compatible

Question

Question:

Does the replacement wf-8955pec charge controller accept lithium or lead acid batteries?

asked by: George

0

Expert Reply:

The wf-8955pec was designed for lead acid batteries. It's charge controller would have been for a lead acid battery but to convert it to lithium you would need the part # PD4655V and you'd be set.

expert reply by: Jameson C

0

Answer 1

The Electric Trailer Brake Kit - 10 inch - Left and Right Hand Assemblies - 3,500 pounds #AKEBRK-35 is the correct brake set up for your Kelsey Hayes 602027 and 602028 and even though your trailer is rated for 2,750 pounds the 3,500 pound brakes will…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 12

To install a 7-way connector on your 2016 Subaru Outback Wagon you will first need a 4-way vehicle wiring harness. I recommend adding the Tekonsha T-One Vehicle Wiring Harness #118467 as it is custom made to plug into the factory harness of your…

view full answer...

Is Charge Controller of WF-8955PEC Lithium Compatible

Products Featured in This Question

Continue Researching