How To Determine The Correct Replacement RV Entry Door Lock For Your RV

Question

Question:

Curious about RV lock exchange

asked by: Patrick B

0

Expert Reply:

If you're wanting to swap out your RV entry door lock then you'll need to first remove the inside portion of your current lock so that you can get access to the cutout hole. You can then measure the height and width of the hole to pick the correct replacement. The Global Link # GL55VR you were looking at requires a 3-3/4" tall x 2-3/4" wide cutout hole, which is pretty standard sizing for most trailers.

expert reply by: Kevin C

0

Answer 1

You can utilize a power wall remote switch #VC0533-03-A or #VC0533-02-A (black or white). A rocker switch #BL0108-00 will work and you will need 2 of them. The installation kit #344270KITW will come with screws, tape, and sealant. You will also need…

view full answer...

Answer 2

Hey Chris, the closest option to what you are looking for would be the Ventline Ceiling Garnish part #VA0445-28 which is birch white like you asked for and is basically exact same dimensions except is 1/8 of an inch taller.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 6

Hi Shaun, I can definitely help with that. From what we typically see on the 2020 Forest River Wolfpack 365PACK16, the most common landing gear setup is the Lippert/Venture style system with 33-1/2 inch outer tubes and 15-1/2 inch inside-to-inside…

view full answer...

Answer 7

Hello Nick, thanks for reaching out. The Lippert Electric Landing Gear #LC333964 is a standard landing gear set, so it should work on your Laredo 5th wheel. There is no way to confirm this using just the make and model though, so some additional…

view full answer...

Answer 8

Unfortunately you can not Doug. The factory hitch on your 2020 Ford F-150 Lariat is part of the rear step-bumper assembly. It's bolted to your frame and then the step-bumper bolts to the trailer hitch. Removing the factory hitch removes the…

view full answer...

Answer 9

Hi Jeff, The K-Source Snap & Zap Custom Towing Mirrors part #KS69NQ will work with your Lariat mirrors while allowing you to retain the use of the camera and side lights! These mirrors are specifically designed to match the contours of the side…

view full answer...

Answer 10

Hey Kurt, yes the correct gap for SumoSprings Solo kits like the part #SS88UV is 1/2 inch to 1 inch like you mentioned. Did you install this already?

view full answer...

Answer 11

Hi John! The Firestone Ride-Rite Air Helper Springs 2627 (our part #F59VV) is technically for the onboard scale option, but it is actually the one you are going to want for your 2022 Ford F-150. The rear axle position sensor for the self-leveling…

view full answer...

Answer 12

Hello Skip, Thanks for writing in! Welcome to etrailer, glad you found us. The Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Rear Axle #AL67PD will be a great fit for your 2025 Ford F-150 Lariat. The great news…

view full answer...

How To Determine The Correct Replacement RV Entry Door Lock For Your RV

Product Page this Question was Asked From

Continue Researching