Diameter of Mounting Holes on Buyers Products 50 Ton 10-Hole Air Compensated Pintle Hook

Question

Question:

What is the diameter of the mounting holes ? 3/4?

asked by: Chris

0

Expert Reply:

The mounting holes on the # 337PH55AC have a 0.812" diameter.

expert reply by: Robin H

0

Answer 1

The Buyers Products 45 Ton Pintle Hook #337PH45 does not have the 4 inch square bolt pattern but rather uses a different pattern. Vertically the holes are 3 inches on center. Horizontally the top row is 5-1/4 inches on center and the bottom is 6-1/2…

view full answer...

Answer 2

The upper holes for the Buyers Products 45 Ton 4-Hole Air Compensated Pintle Hook #337P45AC4 are spaced 5-1/4" on center. The lower holes are spaced 6-1/2" on center. The distance from the upper holes to lower holes are spaced 3" on…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 7

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 8

This is a great choice Joe and thanks for reaching out! Weigh Safe True Tow Weight Distribution Hitch #WS49MR would be a good match for your setup. Since your Grand Design toy hauler will have a loaded tongue weight between 1,300 and 1,600 lbs, this…

view full answer...

Answer 9

Hey Doug. So long as your Husky 5th wheel hitch isn't three decades old you shouldn't have any issues attaching it to the B&W Custom Installation Kit w/ Base Rails item #BWRVK2402. Most 5th wheel hitches for the last 20 years have used…

view full answer...

Answer 10

Hey Ken! Instead of worrying about fitment and a potential return I can give you some measurements so you can figure it out before ordering. The standard shank on the B&W Continuum Weight Distribution System #BW28FR is 11-3/8" from the…

view full answer...

Answer 11

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 12

Hi Ryan! I see you ordered the DeeMaxx set already, but I still wanted to get you an answer to your question. The only real difference between the Dexter Trailer Idler Hub Assembly for 5,200-lb to 7,000-lb Axles - 8 on 6-1/2 - Galvanized #8-231-50UC1…

view full answer...

Diameter of Mounting Holes on Buyers Products 50 Ton 10-Hole Air Compensated Pintle Hook

Product Page this Question was Asked From

Continue Researching