Plug And Play Pigtail For The Tekonsha P3 Brake Controller On A 2006 Dodge Ram Pickup

Question

Question:

I am looking at the Tekonsha P3 brake controller. My vehicle is a 2006 Dodge Ram 2500 that has the towing package. What is the wiring harness for my vehicle that goes from my factory plug under the dash to the P3 controller, plug and play? Thanks.

asked by: Thomas R

0

Expert Reply:

Yes, there is a plug-and-play pigtail which you can use to install the Tekonsha P3 # 90195 in your 2006 Ram 2500 with the factory tow package. The plug you need is part # 3020-P. The plug will be located under the dash, right behind the parking brake.

I have linked our install video below if you want to take a look.

expert reply by: Jesse M

0

Answer 1

The port you describe does not seem like what you need. You are going to be looking up under the dash for the 4 pin connector wiring harness. It is usually blue but this is not always the case, it can sometimes be gray. On your 2004 Dodge Ram it will…

view full answer...

Answer 2

On the 2006 Dodge Ram 1500 that came with either a factory 4-Way or 7-Way trailer connector the receptacle to plug in a brake controller with a harness such as #3020-P will either be on top of or along the side of a white rectangular box back along…

view full answer...

Answer 3

Hey Abby thanks for all the questions! The first thing I need to mention is you will only have a port to plug in a brake controller if your 2005 Dodge 1500 came with either a 4-way connector or a 7-way connector from the factory. If yours has an…

view full answer...

Answer 4

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 5

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 6

For a 2010 Land Rover Range Rover HSE the correct brake controller install harness is the part #3035-P. For a brake controller I would recommend the Prodigy P3 Brake Controller part #90195. This is our best selling brake controller because of how…

view full answer...

Answer 7

For your 2012 Land Rover the correct harness to install the Prodigy P3 part #90195 is the part #3035-P that you referenced. From 2000 to 2008 Land Rover was actually owned by Ford so it's not a huge surprise the vehicle is using an older Ford…

view full answer...

Answer 8

It sounds like you are hardwiring your Prodigy P2 #90885 trailer brake controller. If the controller is not powering up the issue would be on the black wire that delivers 12V operating power to the controller via a circuit breaker like #PK54230. The…

view full answer...

Answer 9

There is a connector available to connect the P3 controller to the Range Rovers under dash connector for brake controller installation. You can order the P3 #90195 and the proper wiring #3035-P. The connection point for the brake controller wiring…

view full answer...

Answer 10

The Tekonsha Plug-In Wiring Adapter part #3035-P may work with your 2018 Land Rover Range Rover Sport HSE. However, the pins inside the vehicle side brake controller adapter port may not match that of the above harness. The reason for this is that…

view full answer...

Answer 11

For your 2010 Land Rover Range Rover Sport, to connect your Tekonsha Prodigy P3 #90195, the connection point for the brake controller wiring harness #3035-P should be under the dash next to the brake switch to the left of the steering column. The…

view full answer...

Answer 12

Other than some slight cosmetic changes, there haven't been any appreciable changes in the chassis of the Land Rover Range Rover Sport since the first model year of the 2nd generation in 2013. Tekonsha/Draw-Tite nor the rest of the companies have…

view full answer...

Plug And Play Pigtail For The Tekonsha P3 Brake Controller On A 2006 Dodge Ram Pickup

Featured Help Information

Miscellaneous Media

Continue Researching