Brake Controller Install Harness Recommendation for 2010 Land Rover Range Rover HSE

Question

Question:

Do you sell the brake controller wire adaptor specific for a 2010 Range Rover HSE not the Sport model? I dont need it hard wired....there is already an outlet under the front dash to plug into. Thanks,

asked by: Roseann

1

Helpful Expert Reply:

For a 2010 Land Rover Range Rover HSE the correct brake controller install harness is the part # 3035-P.

For a brake controller I would recommend the Prodigy P3 Brake Controller part # 90195. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. This will be the last brake controller you buy. It can easily be transferred to future vehicles as well.

expert reply by: Jameson C

1

Answer 1

Yes, there is a plug-and-play pigtail which you can use to install the Tekonsha P3 #90195 in your 2006 Ram 2500 with the factory tow package. The plug you need is part #3020-P. The plug will be located under the dash, right behind the parking brake.…

view full answer...

Answer 2

For your 2012 Land Rover the correct harness to install the Prodigy P3 part #90195 is the part #3035-P that you referenced. From 2000 to 2008 Land Rover was actually owned by Ford so it's not a huge surprise the vehicle is using an older Ford…

view full answer...

Answer 3

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 4

For your 2010 Land Rover Range Rover Sport, to connect your Tekonsha Prodigy P3 #90195, the connection point for the brake controller wiring harness #3035-P should be under the dash next to the brake switch to the left of the steering column. The…

view full answer...

Answer 5

It sounds like you are hardwiring your Prodigy P2 #90885 trailer brake controller. If the controller is not powering up the issue would be on the black wire that delivers 12V operating power to the controller via a circuit breaker like #PK54230. The…

view full answer...

Answer 6

Other than some slight cosmetic changes, there haven't been any appreciable changes in the chassis of the Land Rover Range Rover Sport since the first model year of the 2nd generation in 2013. Tekonsha/Draw-Tite nor the rest of the companies have…

view full answer...

Answer 7

There is a connector available to connect the P3 controller to the Range Rovers under dash connector for brake controller installation. You can order the P3 #90195 and the proper wiring #3035-P. The connection point for the brake controller wiring…

view full answer...

Answer 8

The Tekonsha Plug-In Wiring Adapter part #3035-P may work with your 2018 Land Rover Range Rover Sport HSE. However, the pins inside the vehicle side brake controller adapter port may not match that of the above harness. The reason for this is that…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Brake Controller Install Harness Recommendation for 2010 Land Rover Range Rover HSE

Continue Researching