Availability Of Trailer Hubs For A Harbor Freight Trailer With A 25 mm Spindle

Question

Question:

need a hub for a harbor freight trailer, the axle spindal size is 25mm can you help me out please

asked by: Scott T

0

Expert Reply:

I can certainly point you in the right direction. The closest thing we have to a 25 mm (0.984") spindle will be hubs that fit a 1" (25.4 mm) straight spindle. For example the Trailer Idler Hub # AKIHUB-440-2-G-1K uses a # L44643 bearing (1" inner diameter). This is a fairly common size for a 2,000 lb trailer axle, which harbor freight trailers are known to use.

Generally we would want you to confirm the bearing numbers and bolt pattern of your hub prior to ordering. The AKIHUB-440-2-G-1K that I mentioned has a 4 on 4 bolt pattern. If this does not match the hub on your trailer, feel free to send me some specs and I am happy to make a recommendation.

expert reply by: Jesse M

0

Answer 1

We have the Easy Grease Trailer Idler Hub Assembly #AKIHUB-440-2-EZ-1K which should fit your Harbor Freight trailer. This idler hub includes bearings for a 1" spindle which is 25.4mm. It has a 4 on 4" bolt pattern. You can verify this is…

view full answer...

Answer 2

Hey Keith, if you exceed the speed rating of your trailer tire you will end up overheating the tire and that will most likely cause it to fail. This is definitely going to be very likely if you are driving 12 to 14 hours at a time. Best option would…

view full answer...

Answer 3

It looks like the Harbor Freight Folding Trailers use a Jeep style fender so if that's the case then the best option we have for replacement is the Single Axle Trailer Fender part #HP99VR which will work just fine with 4.80x12 tires. That said,…

view full answer...

Answer 4

The Kenda Loadstar ST175/80D13 Bias Trailer Tire #AM3S120 that you referenced is going to close that trailer frame to tire gap by almost a full inch. This would put the new tire much too close to the frame on your Harbor Freight Trailer. The issue is…

view full answer...

Answer 5

The Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 60" Long - 2,200 lbs #T20BTR-EZ-6048 will fit any trailer with spring seats 48 inches on center. If you Harbor Freight trailer has leaf springs that are 48 inches on center then you will…

view full answer...

Answer 6

The downside to buying a "bargain" trailer kit is that customer support, both in terms of helpful information and available replacement parts, can be scarce. The other issue is that products made to sell at a tempting price point may not…

view full answer...

Answer 7

Hey David, Unfortunately, Harbor Freight trailers do not use standard spindles and require a 30205 bearing with a specific 0.985" inner diameter. So, while we have bearings and hubs with similar dimensions to theirs, we do not have the exact…

view full answer...

Answer 8

As Harbor Freight constantly uses different parts on their trailers you will need to disassemble one of the hubs to check the bearings and seals. I have included an image below which identifies the location for the bearing and grease seal numbers as…

view full answer...

Answer 9

Harbor Freight trailers are normally not able to work well with other axles because they are not made to industry specs. We do have a kit that will allow you to replace your trailer axle and suspension that will also fit the tires you are seeking. It…

view full answer...

Answer 10

To determine if we have a wheel bearing that will be compatible, you will need to use a digital caliper and take some measurements of your existing spindles. If you reply with the B, C and D dimensions you find (as shown in the diagram I provided), I…

view full answer...

Answer 11

Why were you wanting to swap to a larger wheel? Keep in mind that simply swapping out to a larger wheel won't in and of itself increase the capacity of the trailer (if that's your intention). The capacity of the trailer will be limited to the…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Availability Of Trailer Hubs For A Harbor Freight Trailer With A 25 mm Spindle

Products Featured in This Question

Continue Researching